Lrl from Italy

[liudengyuand]

This is a good way

[liudengyuand]

I think your oscillator should be shielded by a tin box separately

[FrancoItaly]

Originally Posted by liudengyuand

I think your oscillator should be shielded by a tin box separately

Of course, but we must not forget that even the power must be decoupled.

[liudengyuand]

The biggest problem is that the specific frequency responds to the metal, or a certain frequency, or any frequency,

[FrancoItaly]

Originally Posted by liudengyuand

The biggest problem is that the specific frequency responds to the metal, or a certain frequency, or any frequency,

In my opinion there is no specific frequency for metals, the phenomenon exists in a wide range from Khz to infrared. All that remains is to experiment and it is very important to have a field where to do the tests, it is necessary to bury the metals, for example gold / silver and wait at least a few months or less, it depends on the type of soil.

[liudengyuand]

If it has nothing to do with frequency, there is no need to adjust L1 and C10, their resonance frequency is much higher than 8MHZ

[folharin]

Originally Posted by FrancoItaly

In my opinion there is no specific frequency for metals, the phenomenon exists in a wide range from Khz to infrared. All that remains is to experiment and it is very important to have a field where to do the tests, it is necessary to bury the metals, for example gold / silver and wait at least a few months or less, it depends on the type of soil.

exactly sir franco italia !!

[liudengyuand]

I have successfully increased the distance to about 50 meters

[liudengyuand]

Has anyone experimented with using an aluminum box to install the entire circuit? Will it have any effect?

[liudengyuand]

I placed an fm transmitter on the opposite side of the copperware buried for five years, which emits a certain pulse signal. When the transmitter, the metal and the detector are in a straight line, the signal is particularly strong, and the distance has exceeded at least 300m.

[tasmen]

When it is not straight line with metal, do you catch the fm transmitter?

[liudengyuand]

no

[brain]

Originally Posted by liudengyuand

no

Can you publish the fm transmitter scheme you made.

[liudengyuand]

ok

[ERDOGAN37]

https://www.youtube.com/watch?v=SrmxnvivM-0

https://youtu.be/MbOk9o6Fc3M

https://www.youtube.com/3304e2ba-a15...3-fbc22861d48f

[humhum]

Originally Posted by ERDOGAN37

https://www.youtube.com/watch?v=SrmxnvivM-0

https://youtu.be/MbOk9o6Fc3M

https://www.youtube.com/3304e2ba-a15...3-fbc22861d48f

Kayseri , Second video is good , third video link not woks .

[ERDOGAN37]

https://youtu.be/1jSvzxRhjPk

[humhum]

Originally Posted by ERDOGAN37

https://youtu.be/1jSvzxRhjPk

Which version of Franco LRL build You and test in upper Video.

[tasmen]

Hello mr Franco.
I hope you are well.
I have some questions.
First i create sensor stage quartz 8Mhz and is ok (out 5.85V and when I touch the antenna the voltage drops 5.7v dc).
When I connect the antenna amplifier stage (without the display stage) what value should I have at the exit?
I set it with the potetiometer to 5.7v but when I touch the antenna the voltage does not drop. it's correct? (without display stage).
Thank you in advance.

[FrancoItaly]

Originally Posted by tasmen

Hello mr Franco.
I hope you are well.
I have some questions.
First i create sensor stage quartz 8Mhz and is ok (out 5.85V and when I touch the antenna the voltage drops 5.7v dc).
When I connect the antenna amplifier stage (without the display stage) what value should I have at the exit?
I set it with the potetiometer to 5.7v but when I touch the antenna the voltage does not drop. it's correct? (without display stage).
Thank you in advance.

Yes, that is correct, however it is better to try the operation without the antenna amplifier on the test field, also to establish the actual improvement.

[omar]

Hello Franco. The phenomenon is an invisible light beam of negative electrons similar to a cathode ray. It is the resonance of the material. What you lack is a transmitter circuit to raise the kinetic energy of the photoelectrons, so that they can be easily captured. Your device captures them as stray signals from close distances.

[FrancoItaly]

Originally Posted by omar

Hello Franco. The phenomenon is an invisible light beam of negative electrons similar to a cathode ray. It is the resonance of the material. What you lack is a transmitter circuit to raise the kinetic energy of the photoelectrons, so that they can be easily captured. Your device captures them as stray signals from close distances.

I doubt anyone knows exactly how the phenomenon works, we just know that it works over a wide range of frequencies. All the rest are theories to be proved without considering that whatever is transmitted must reach tens of meters away and be directive. I am convinced that all lrls are passive receivers and even if there is a transmitting led, it cannot get very far.

[Babak51]

Hello. I had good discoveries. Thank you, Mr. Franco, Italy. Although the radius of my discoveries was not more than 4 meters, but I love the circuit of this device. Thank you.

[Babak51]

Originally Posted by liudengyuand

Has anyone experimented with using an aluminum box to install the entire circuit? Will it have any effect?

Not because it is said to interfere with signal reception.

[FrancoItaly]

Originally Posted by Babak51

Hello. I had good discoveries. Thank you, Mr. Franco, Italy. Although the radius of my discoveries was not more than 4 meters, but I love the circuit of this device. Thank you.

I am happy that you have had good results with my lrl and I thank you for having said it publicly for the benefit of those who do not believe in the phenomenon or at least are in doubt. Other forum members confirmed it privately but asked me not to disclose it.