Tuned dowsing rods

[Mike(Mont)]

This is an old site, not sure if it is still active.

http://www.precisiondowsing.com/index.htm

[Geo]

Very good, it works.

Mike thanks

[Mike(Mont)]

I don't understand the reasoning of the length of the coil being 32 times the diameter?

[Mike(Mont)]

The original info I got had 32x but I see now it says wire length is 64 x the length of the center core conductor.

[Geo]

Originally Posted by Mike(Mont)

I don't understand the reasoning of the length of the coil being 32 times the diameter?

Me too....

[Mike(Mont)]

Been thinking about these rods and I don't see much need for pure copper. I found some 3/16" x .014" (4.76 mm x .355 mm) brass tubing and some 5/32" (3.96 mm) brass rod for the handle. I have some thin magnet wire don't know the gauge but it's thin, maybe too thin to work with, but it would be much lighter weight. Probably will not be able to match his 64x.

[Geo]

You know very good that if you have the dowsing then no need for any mod on rods

[Mike(Mont)]

He claims experienced dowsers can get better results. I don't know, he throws a lot of terms out there to confuse the buyer. LOL Just by extrapolation I come up with about 1200 turns on the brass tubing. I plan to use an electric drill to wind it and just guess about how many turns per inch. I don't have a clue what frequency he is trying to get for a given magnetic field strength. I come up with about 18 meters for 54000 field strength. Apporximately 18 meter half-wave dipole is for 8.3 MHz. What is that? I sure don't know.

BTW, I had an old Fred Stewart rod had a coil of wire on the rod near the handle.

This thing is probably a big waste of time. LOL

[Geo]

Originally Posted by Mike(Mont)

He claims experienced dowsers can get better results. I don't know, he throws a lot of terms out there to confuse the buyer. LOL Just by extrapolation I come up with about 1200 turns on the brass tubing. I plan to use an electric drill to wind it and just guess about how many turns per inch. I don't have a clue what frequency he is trying to get for a given magnetic field strength. I come up with about 18 meters for 54000 field strength. Apporximately 18 meter half-wave dipole is for 8.3 MHz. What is that? I sure don't know.

BTW, I had an old Fred Stewart rod had a coil of wire on the rod near the handle.

This thing is probably a big waste of time. LOL

I am sure that you have better ways to spend your time!!

[Mike(Mont)]

One thing I gleaned from this webpage has to do with rod length. He says rod length between 6.5" - 13.75" (16.5 cm - 35 cm) and magnetic field strength between 23,000 - 60,000. When I figure for my field strength 54130, it comes out to approximately (in my head without calculating) rod length just under 13" (33 Cm). This is almost exactly what I have been using for rod length and I have a feeling that this is an important parameter. I have never seen it mentioned that there is a correlation between rod length and magnetic field strength.

[Geo]

At my city the magnetic field strength is near to 46000 and the rods that i use are near to 45cm, farfrom 33cm that the webpage says!!!

[Mike(Mont)]

Maybe that is why you do not like L-rods. LOL Just joking From what I calculate you should be using rod length 28 cm.

[Mike(Mont)]

Actually that is the length of the coil not the entire rod. So I guess it does not match what I use, either.

[Geo]

I believe that if you are good at dowsing then you are good with any rod at any place.

[Mike(Mont)]

Yes, and on the other end of the scale someone who is a poor dowser even a good rod will not help much. My firm belief is people tend to psyche themselves out and think too much. I say pick a spot out in front of you a ways and look at it and don't think about the dowsing. It is essential to keep the conscious mind out of the way.

Like Hills says, a good carpenter can use most tools and get them to work but he cannot drill a one inch hole with a two inch bit.

[Geo]

Originally Posted by Mike(Mont)

Yes, and on the other end of the scale someone who is a poor dowser even a good rod will not help much. My firm belief is people tend to psyche themselves out and think too much. I say pick a spot out in front of you a ways and look at it and don't think about the dowsing. It is essential to keep the conscious mind out of the way.

Like Hills says, a good carpenter can use most tools and get them to work but he cannot drill a one inch hole with a two inch bit.

Unless you're pretending not to see the hole bigger. It is a matter of psychology !!