My TOTeM project

[king40]

Originally Posted by Nicolas

Hi mustetfa

Good work for your PCB

But we like some details for your LRL. If it possible

good question

[Fred]

Originally Posted by Nicolas

Hi Mustefa Thank you.
Here is your PCB

Hi Nicolas,
You noticed the problems on this pcb ?
Just to call you attention.

[Nicolas]

Originally Posted by Fred

Hi Nicolas,
You noticed the problems on this pcb ?
Just to call you attention.

Yes my friend thanks I have said that to Our friend Mustefa for correction.

and I have a lot of PCB and I have to check all.

[Fred]

Exactly
Good work !

[mustefa ubram]

hi nicolas and other freinds
I've looked pcb.pcb is correct.The problem is related to printing pcb.You have prepared in the traditional way

[kahyal]

Originally Posted by mustefa ubram

hi nicolas and other freinds
I've looked pcb.pcb is correct.The problem is related to printing pcb.You have prepared in the traditional way

it's for all friends...

[Nicolas]

Originally Posted by mustefa ubram

hi nicolas and other freinds
I've looked pcb.pcb is correct.The problem is related to printing pcb.You have prepared in the traditional way

Thanks dear

This method of printing is professional my friend not traditional
I work not manual
I am a professional and I am a seller too.
my prototypes are without varnish without epoxy without silkscreen without enameling
but the other yes.

[roccocoin]

Originally Posted by Qiaozhi

The TX coil has 75 turns of 0.56mm enameled wire on an 80mm diameter former. The resonant frequency is not that critical as the TX is a forced oscillator running at around 65kHz.
The RX coil has 100 turns of 0.56mm enameled wire.

Without the coils connected, you can test the power supplies are correct, and that the TX oscillator is working. If you connect the RX coil, it will be possible to use the device in passive mode, as there is no need to balance the coils. Balancing will be required after you add the TX coil.

still a pleasure, I wanted to know the diameter of the coil rx? 100 tourn 0.56 thread, but the diameter? tank
please give me this information because I can not find it and I did not pre-read the book, then I will buy sicuramente.tank and good evening

[Qiaozhi]

Originally Posted by roccocoin

still a pleasure, I wanted to know the diameter of the coil rx? 100 tourn 0.56 thread, but the diameter? tank
please give me this information because I can not find it and I did not pre-read the book, then I will buy sicuramente.tank and good evening

The RX coil is wound on a ferrite rod.
See Chapter 14 of ITMD.

[roccocoin]

Originally Posted by Qiaozhi

The TX coil has 75 turns of 0.56mm enameled wire on an 80mm diameter former. The resonant frequency is not that critical as the TX is a forced oscillator running at around 65kHz.
The RX coil has 100 turns of 0.56mm enameled wire.

Without the coils connected, you can test the power supplies are correct, and that the TX oscillator is working. If you connect the RX coil, it will be possible to use the device in passive mode, as there is no need to balance the coils. Balancing will be required after you add the TX coil.

hello, but you rx 100 tourn but the diameter and how? how many and great the rx 100 tourn? and not explained that diameter and rx can please tell me how and the diameter of the coil rx? tank

[roccocoin]

Originally Posted by roccocoin

hello, but you rx 100 tourn but the diameter and how? how many and great the rx 100 tourn? and not explained that diameter and rx can please tell me how and the diameter of the coil rx? tank

and right mounting for tx and rx? correct ?tanks

[roccocoin]

Originally Posted by roccocoin

and right mounting for tx and rx? correct ?tanks

La bobina TX dispone di 75 giri di 0,56 millimetri filo smaltato su un diametro di 80 millimetri ex. La frequenza di risonanza non è critica come il TX è un oscillatore forzato esecuzione a circa 65kHz.
La bobina RX dispone di 100 spire di 0,56 millimetri filo smaltato.

Senza le bobine collegate, è possibile verificare gli alimentatori sono corrette, e che l'oscillatore TX sta lavorando. Se si collega la bobina RX, sarÃ* possibile usare il dispositivo in modalitÃ* passiva, in quanto non vi è alcuna necessitÃ* di equilibrare le bobine. Bilanciamento sarÃ* richiesto dopo aver aggiunto la bobina TX.

P.S.You can figure out what and where the TX and RX and the? you have made a big mess that you can not figure out what and where the coil and the coil TX and RX, please, a little respect for those who are not so handy with electronics ...... the RX AND ROLL WITH FERRITE AND 75 OF THE SPIRE? THE TX AND EXTERNAL COIL WITH SPIRE 100? TANKS

[Qiaozhi]

Roccocoin - If you want to make a post in your own language, then please also provide an English translation.
Please read the forum rules -> Basic Rules of the Forums

In particular, this part: "Although this forum is open to everyone everywhere, I ask that posts be written in English to maximize participation. If English is not your native language, just do the best you can."

[roccocoin]

Originally Posted by roccocoin

La bobina TX dispone di 75 giri di 0,56 millimetri filo smaltato su un diametro di 80 millimetri ex. La frequenza di risonanza non è critica come il TX è un oscillatore forzato esecuzione a circa 65kHz.
La bobina RX dispone di 100 spire di 0,56 millimetri filo smaltato.

Senza le bobine collegate, è possibile verificare gli alimentatori sono corrette, e che l'oscillatore TX sta lavorando. Se si collega la bobina RX, sarÃ* possibile usare il dispositivo in modalitÃ* passiva, in quanto non vi è alcuna necessitÃ* di equilibrare le bobine. Bilanciamento sarÃ* richiesto dopo aver aggiunto la bobina TX.

P.S.You can figure out what and where the TX and RX and the? you have made a big mess that you can not figure out what and where the coil and the coil TX and RX, please, a little respect for those who are not so handy with electronics ...... the RX AND ROLL WITH FERRITE AND 75 OF THE SPIRE? THE TX AND EXTERNAL COIL WITH SPIRE 100? TANKS

Excuse me immensely, I had translated for me and then I did copy and paste directly. ancora.ma excuse me could you tell me where the coil and the tx and rx? that rx and the ferrite the baby? tanks

[Morgan]

Originally Posted by Qiaozhi

Roccocoin - If you want to make a post in your own language, then please also provide an English translation.
Please read the forum rules -> Basic Rules of the Forums

In particular, this part: "Although this forum is open to everyone everywhere, I ask that posts be written in English to maximize participation. If English is not your native language, just do the best you can."

Hello

I decide to put here the news of a GREAT TREASURE OF GOLD COINS found recently in Greece with the PDK-2.3 model, this is not propaganda for sale PDKs, its the amazing find of a ceramic pot with a hoard of gold coins.
I stay silent about WHO FOUND the hoard, but it is cientific evidence that the gold inside sealed ceramic pot also irradiate the PHENOMENON.
About DISTANCE and DEPTH i dont know yet,this is today amazing news.
It willbe great if the person who foud the pot,give a gold coin as a souvenir

Regards all

[mustefa ubram]

hi to all
I would like to start construction.This is my box

[Goldmaxx]

Originally Posted by mustefa ubram

hi to all
I would like to start construction.This is my box

Hello mustefa ubram,

Congratulations, looks very good. I 'm very curious about your experience with your Totem project.

Best Regards
Goldmaxx

[mustefa ubram]

hi Qiaozhi , goldmax ,morgan
Please help to adjust and calibrate totem?

[adamas1]

Is correct when approaching my hand at TOTEM was whistling

[rtl_2014]

dear friends.
after 2 week working on my totem pd i can test it on passive mode.
it work good with electromagnetic filed and ionic radiation devices.
at last test ( attached video) near the ferrite loop it can sense my watch tick tick and beep for each second changed.
http://youtu.be/Sdyxsla7lJc
but on active mode when i release the active/passive Switch to active mode red and yellow LED and the meter and buzzer turned to ON and by changing the active pot nothing happens
i changed position of ferrite and test it on each position please help me to calibrate may totem pd.
tanks

beast regards.

[Qiaozhi]

Originally Posted by rtl_2014

dear friends.
after 2 week working on my totem pd i can test it on passive mode.
it work good with electromagnetic filed and ionic radiation devices.
at last test ( attached video) near the ferrite loop it can sense my watch tick tick and beep for each second changed.
http://youtu.be/Sdyxsla7lJc
but on active mode when i release the active/passive Switch to active mode red and yellow LED and the meter and buzzer turned to ON and by changing the active pot nothing happens
i changed position of ferrite and test it on each position please help me to calibrate may totem pd.
tanks

beast regards.

The ferrite coil adjustment procedure is on page 231 of ITMD.

[Saiman]

Originally Posted by koko

Hello Qiaozhi

Thank you very much for your Reply,please if you can help whit this photo

HELP ME
you have 4 switches, I saw
Why should the name of each switch
and how to connect with PCB

[Saiman]

Originally Posted by Saiman

HELP ME
you have 4 switches, I saw
Why should the name of each switch
and how to connect with PCB

Thank

[Qiaozhi]

Originally Posted by Saiman

HELP ME
you have 4 switches, I saw
Why should the name of each switch
and how to connect with PCB

See page 241 of ITMD.

[Saiman]

Originally Posted by Saiman

HELP ME
you have 4 switches, I saw
Why should the name of each switch
and how to connect with PCB

hi all friends. I hope all healthy.
I have a problem with the switch LRL TOTEM PD
see all photos in LRL Totem Pd forum, I made the decision. Switch probably like this
I really hope any help from friends forums.
to correct any that is not true.
Thank for all.