My TOTeM project

[Goldmaxx]

Today the sun was shining and it was a little bit heater.
On this occasion have taken my TOTeM and went for a walk for two hours in the forest.
I wanted to see how the PD outdoors reacts.
It was just so and no special place where I went.
I've experimented a bit with the settings and have all the time no signal.
But suddenly I had a place where I had a good signel. I could not pinpoint exactly, but it was a clear signal.
I have found nothing and I then aborted the search because it was very cold again.
It was nothing special, but very interesting.
In the video, the PD was set in the active mode.
But I had the same signal in the passive mode.

If the weather is good next weekend, I'll try my luck at a good place.

here is the video from my trip

[matrix]

all PERFECT!!!
I wish a hot Sunday for you next week ; Again wait.

best wishes

[vali]

hello gold maxx .
I congratulate you. But the sensitivity is set too high.
regards .

[DrTech]

Originally Posted by Goldmaxx

Hi DrTech
sorry but you must the distance with calibrate find out yourself, because each ferrite coil reacts differently and most importantly,
you will be a different distance to the TX coil as I have.
I can therefore give you no distance, because I do not even know if mine are correct.
This will to prove only in the field test.
But you must the RX coil (ferrite) try to find the zero point to the TX coil.

Regards

Goldmax, you change the polarity of transistors BC108 (U8,U5,U6) because I do not work because the Emitter and collector are changed depending on the circuit and is assembled, the difference is in the way he did Sneshko PCB and the other as you assemble the pcb .

After making the modification worked out perfectly in passive mode, but NOT active mode. I change the BC108 transistor U8 new one.

It works in active mode but goes beep TX and RX must be far apart to stop beeping., I think they are at the same frequency

Regards...

[detectoman]

i cant open the goldmaxx video archive, can anybody please put these in other format? thanks

[detectoman]

dr tech, may be you should put frecuencies change or to other armonic´´ or lowering these or higest
doctor tecno, puede ser usted necesite cambiar las frecuencias o a otras armonicas" o bajar estas o elevarlas, o no es debido el tamaño de la bobina y le gana a la recepcion preactivandola, pruebe con otra bobina mas chica a la misma frecuencia o pongala de modo diametralmente en diagonal, como se hace con los dos cajas, inclinandola un poco y poniendola a la debida distancia, tal ves eso le ayude, sino le indico por correo otras estrategias saludos

[detectoman]

hello we need a complete spanish long range forum section or hibirid spanglish, any like to open? may be is very difficultous read by who no understand our bad english apologies

[matrix]

Originally Posted by detectoman

i cant open the goldmaxx video archive, can anybody please put these in other format? thanks

This is a famous format(MP4) . Extract it in winrar then can be played with jetaudio

[detectoman]

i cant open these jjajaja and i yes have winrar, i not understand..

[Morgan]

Originally Posted by detectoman

i cant open these jjajaja and i yes have winrar, i not understand..

i can hear the video sound but no image...

[Goldmaxx]

Originally Posted by matrix

all PERFECT!!!
I wish a hot Sunday for you next week ; Again wait.

best wishes

Hello matrix
Many thanks. I will all about my next steps up to date.
I myself am very curious.

best Regards

[Goldmaxx]

Originally Posted by vali

hello gold maxx .
I congratulate you. But the sensitivity is set too high.
regards .

Hi vali

Many thanks for the congratulations. I have only briefly tested the totem.
Next trip I'll think of you.

Many greetings

[Goldmaxx]

Originally Posted by DrTech

Goldmax, you change the polarity of transistors BC108 (U8,U5,U6) because I do not work because the Emitter and collector are changed depending on the circuit and is assembled, the difference is in the way he did Sneshko PCB and the other as you assemble the pcb .

After making the modification worked out perfectly in passive mode, but NOT active mode. I change the BC108 transistor U8 new one.

It works in active mode but goes beep TX and RX must be far apart to stop beeping., I think they are at the same frequency

Regards...

Hi DrTech

Congratulations to your totem, he looks very good.

I built my PCB after Qiaozhi's instruction in his book, and you can only say that the PCB works so very well.
Qiaozhi is an expert in this area and I can only recommend them to you even after his instruction to build.

But as is to see them on your picture, I would say that the distance from the RX coil to the TX coil is too low and therefore you can not find the zero point.
Have you installed the ferrite coil in the box?

Regards

[Goldmaxx]

Originally Posted by detectoman

i cant open the goldmaxx video archive, can anybody please put these in other format? thanks

Hello detectoman
matrix is right, it is a MP4 format and it is extract with winrar.
But I have here still an AVI format for you.
Sorry for the bad quality, but I can unfortunately post only 1 MB.

Regards

[Goldmaxx]

And here a FLV format in slightly better quality.

[Goldmaxx]

Originally Posted by Morgan

i can hear the video sound but no image...

Hi Morgan
You have already seen the video.

Best regards

[Morgan]

Originally Posted by Goldmaxx

Hi Morgan
You have already seen the video.

Best regards

yes,and it seems the ToTeM locate a target in the forest,now you need the practice to follow the signals and PINPOINT the object.
maybe Qiaozhi create a super LRL ? ...

[detectoman]

the long range detection today arrive, with morgan alonso 2006 year pd revelations, soon the convencional plate md of enginers productions, be past thing´s

[detectoman]

arggg, anybody please put these video on basic window media vista formats grrrrrrr

[detectoman]

at most, i have total stronger sound but whitout imageee grrrrr waaaa, no sir, i not like to dowload any other new video programs by each new video view what yours posted

[Goldmaxx]

Originally Posted by Morgan

yes,and it seems the ToTeM locate a target in the forest,now you need the practice to follow the signals and PINPOINT the object.
maybe Qiaozhi create a super LRL ? ...

I will again go to this place, and try to locate the signal better.
I've watched the MINEORO video. It is really very well explained how to search with a PD.

Yes, maybe Qiaozhi has developed really a super LRL.
That would be really brilliant.
I'm very curious about the next tests with the TOTeM.

[Goldmaxx]

Originally Posted by detectoman

at most, i have total stronger sound but whitout imageee grrrrr waaaa, no sir, i not like to dowload any other new video programs by each new video view what yours posted

Hello detectoman

Okay, what kind of format need you?
I will you make it so you can watch the video too.

[matrix]

Hi Goldmaxx
what is happened for you ?
we are waiting here 2weeks,
Do you have find treasure in the forest ?

Best wishes

[Morgan]

Originally Posted by matrix

Hi Goldmaxx
what is happened for you ?
we are waiting here 2weeks,
Do you have find treasure in the forest ?

Best wishes

yes,i am curious too...

[detectoman]

i have window media player