Dowsing Rod for 2012

[jack]

Originally Posted by Geo

About winding i wrote at begining.... you must wind 280turns onto the antenna as at photos. I put a paper onto antenna and after it i wound 280 turns on one layer with wire 0.15 mm diameter. That is all.
Antenna is 80 cm long.

Regards

tank you very much dear geo
Please answer my other questions about this device
1.please give a list and description of parts and machine work?
2.To what depth and distance can detect metals?
3.When it detects that the metal reacts?
4.I also recognize that new metal?Or is the only metals that traditionally defines the soil?
tank you
best wish for you in new year
jack

[Geo]

Originally Posted by J_Player

Hi Geo,

I am wondering what the brass and steel part on the outside of the box are for (see image below).
What is their purpose in this transmitter? Also, how are they connected in the circuit?

Other questions:
1. How is this transmitter used?
2. Does the transmitter connect to dowsing rods or to a ground probe?
3. Is the transmitter held in the hand, or is it placed at a distance from the dowser?


Best wishes,
J_P

Hi J_P.
1. You turn the swich to on and the transmitter works.
2.Transmiter is connected to antenna via the L1.
3.Transmitter is inside the plastic box. You don't keep nothing, only the handle of rod.

Tommorrow i willl try to draw a schematic of how all are connected.

Regards

[teknoloji]

Originally Posted by J_Player

Hi Geo,

I am wondering what the brass and steel part on the outside of the box are for (see image below).
What is their purpose in this transmitter? Also, how are they connected in the circuit?

Other questions:
1. How is this transmitter used?
2. Does the transmitter connect to dowsing rods or to a ground probe?
3. Is the transmitter held in the hand, or is it placed at a distance from the dowser?


Best wishes,
J_P

Agree with your opinion.
This put a handle is missing.

[teknoloji]

Originally Posted by Geo

This is a free project.
If you don't know to use a Lrod then let it.
Also if this is waste of your time then read something other project. This is not for you.

Regards

of course you allow.
I have wasted time to spend alone in labor.

Regards

[Fred]

I see,
I found it strange because i would have used this kind of circuit...

[Geo]

If we wanted a fixed frequency with a fixed duty cycle then only one 555 as astable was ok.
But i had problem at range from 3 to 70 Hz with fixed duty cycle. A very cheap IC was the solution.

Regards

[kostas87]

Hello everyone ... Merry Christmas ..! hi geo!
who worked on specific lrl a cave, you should pass directly above to react rod, with the appropriate settings for this!
GREETINGS ..

[Geo]

Originally Posted by kostas87

Hello everyone ... Merry Christmas ..! hi geo!
who worked on specific lrl a cave, you should pass directly above to react rod, with the appropriate settings for this!
GREETINGS ..

Hi Kosta.
Χρονια πολλα.
You tried this LRL. It is not for everyone, they must know about dowsing so to work with it.

Regards

[jack]

hi geo
Please reply to post number26
waiting for your answer
with respect

[Fred]

Originally Posted by Geo

If we wanted a fixed frequency with a fixed duty cycle then only one 555 as astable was ok.
But i had problem at range from 3 to 70 Hz with fixed duty cycle. A very cheap IC was the solution.

Regards

Of course, but this is just an idea : You just need to install a pot in place of the 784k resistor, and you have a variable frequency. Then another pot in place of the 6.k8 resistor, and you have variable duty cycle (pulse) length. And the 555 is able to drain or source 300ma .
And voilá ! two pots , 2 leds on the 555 output , one for pulse length, and one for off state, just what you need to make it look good, and with enough controls to make it with many possible combinations and discrimination to olives .

Best regards Geo

[Geo]

Originally Posted by Fred

Of course, but this is just an idea : You just need to install a pot in place of the 784k resistor, and you have a variable frequency. Then another pot in place of the 6.k8 resistor, and you have variable duty cycle (pulse) length. And the 555 is able to drain or source 300ma .
And voilá ! two pots , 2 leds on the 555 output , one for pulse length, and one for off state, just what you need to make it look good, and with enough controls to make it with many possible combinations and discrimination to olives .

Best regards Geo

Yesssss

Regards

[Geo]

Originally Posted by jack

tank you very much dear geo
Please answer my other questions about this device
1.please give a list and description of parts and machine work?
2.To what depth and distance can detect metals?
3.When it detects that the metal reacts?
4.I also recognize that new metal?Or is the only metals that traditionally defines the soil?
tank you
best wish for you in new year
jack

Hi Jack.
This is a LRod. You must know dowsing so to work with this. What this mean, that if you are a good dowser then you can detect either fresh and buried metals. Depth is bigger than what you can dig. Detecting distance.... i don't know but i believe to be more than 30m. If you are not a dowser then don't construct it, you need time to learn it

Regards

[Geo]

Here a schema of the electronic rod.

[jack]

When the LED light in this device?

The brass has a connection with you?

Sense how the metal reacts when the device is detected?

[Geo]

another schema....

[Geo]

Originally Posted by jack

When the LED light in this device?

The brass has a connection with you?

Sense how the metal reacts when the device is detected?

The brass base and stainless shaft, connected to the antenna.
You can put the led at every place you like!!!
When you detect a metal then the rod turns....
But i will tell again, if you don't know how a Lrod works, then stop the project.

Regards

[jack]

Thank you, Geo
After the brass rod through brass handle is in contact with the operator?same lrls
The schematic is attached to a brass rod bearing and the bearing to handle bronze.When I go step by step, because all Elements (rice sticks - Bearings - The Bronze) The telescopic antenna is connected to each other and are connected to the operator.
Is that true?

[Geo]

Originally Posted by jack

Thank you, Geo
After the brass rod through brass handle is in contact with the operator?same lrls

Yes.

[jack]

image of my Lrod

[Geo]

Jack, very good, congratulations.
I want to see the side to the handle and the bearing

Regards

[jack]

Originally Posted by Geo

Jack, very good, congratulations.
I want to see the side to the handle and the bearing

Regards

Inevitably dear Geo
I have not built yet, and those bearing.I make batches and the ball and I'll show you tomorrow
You must handle is made ​​of bronze?Or any other conductive metal can I use?
Like copper or stainless steel or brass?
with respect dear geo

[jack]

the end my project.photos for you

[jack]

Hi Geo
I will make the device work.
I've tested it, but it does not work
How do I test this device please help?

[WM6]

Originally Posted by jack

Hi Geo
I will make the device work.
I've tested it, but it does not work
How do I test this device please help?

This is (electronic) dowsing rod.

To put dowsing rod "to work", you need to be a dowser.

No one dowsing rod is working separate by switch ON and without elementary role of dowser.

[jack]

Originally Posted by WM6

This is (electronic) dowsing rod.

To put dowsing rod "to work", you need to be a dowser.

No one dowsing rod is working separate by switch ON and without elementary role of dowser.

I got a hunk of copper buried under the soil. But the device did not show any reaction.
What do you mean the dowser?
Please define for me the dowser?