![]() |
#1
|
||||
|
||||
![]() |
#2
|
||||
|
||||
![]()
this circuit is part 85 of my dch front
what is the purpose of it? |
#3
|
|||
|
|||
![]()
its a transmitter. pin 2 and pin 6 have to connect its other to properly run this transmitter
|
#4
|
||||
|
||||
![]()
Hi folharin
I have a question for you. Has i understood, this transmiter is fom your DCH 85, correct? An if so, what is the coil wire diameter? What are your expiriencies with DCH 85? In advance many thanks Nelson |
#5
|
||||
|
||||
![]()
Transmitting to 949 hz ?????????
![]() Capacitor (C):10nanoFarad (nF) microFarad (μF)Resistor 1 (R1):150ohms (Ω) kilohms (kΩ) megaohms (mΩ)Resistor 2 (R2):1ohms (Ω) kilohms (kΩ) megaohms (mΩ)Frequency:949.343HzCycle Time:1.053msDuty Cycle:99.34%Time High:1.046msTime Low:6.930μs |
#6
|
||||
|
||||
![]() coil tuned to 42.5 Khz..... ?????? ![]() Contur calculation Circuit capacitance: 100 nF Frequency of a circuit: 42.5 kHz =>Inductance of a circuit: 140.237 µH ---------------------------------------------------------------------------- Inductance calculation — Multilayer coil Coil inductance 140.237 µH Diameter of former D: 40 mm Length of winding l: 5 mm Diameter of a wire d: 0.3 mm =>Thickness of the coil c: 1.313 mm =>Resistance of the coil 1.717 Ohm =>Necessary length of the wire: 7.034 m =>Number of turns of the coil: 54.699 |
#7
|
||||
|
||||
![]()
drtech, of where take you these messurements?¿?¿¿¿¿ you have a dchs 85?
may be these trasmiter send any low armonic drtech de donde tomaste esas mediciones? tienes tu una dchs 85? puede ser que ese trasmisor mande algunas bajas armonicas ![]() |
#8
|
||||
|
||||
![]() Quote:
No yo no tengo DCH85... The data are compared to the scheme public. of Folharin I have MORE THAN ONE YEAR RESEARCH ON LRL, Everyone knows about the detection circuit .. but the TX and RX frequency is unknown to the Fenomeno (buried metals) .. It can be assumed RX 60-62 kHz and 15-25 kHz TX But I think that is not the way. In the Totem TX RX 58kHz and 60kHz, I have to adjust it because it autodetects. this I have become the "lost frequencies Hunter" and not in "Treasure Hunter" .... ![]() Los datos son respecto al esquema que se publico. de Folharin tENGO MAS DE UNA AñO INVESTIGANDO SOBRE LOS LRL, Todos saben acerca del circuito de deteccion.. pero la frecuencia de TX y RX es desconocida para el Fenomeno(metales enterrados).. Se puede presumir RX 60 a 62 khz y TX 15 a 25 KHZ Pero creo que ese no es el camino. En el Totem TX 58KHZ and RX 60KHZ, tengo que ajustarlo, porque se autodetecta. esto me ha convertido en el "El cazador de frecuencias perdidas" y no en "cazador Tesoros".... |
#9
|
||||
|
||||
![]()
this is the front of dch 85 yes
Tests made on tv tube and fluorescent with and without this circuit and the results are the same |
#10
|
||||
|
||||
![]()
hunter lost frecuences? hahaiahaia drtech, how autodetection? then you need low the frecuences or put these very higer hahaha ( risas en ingles ) or you need other rx tx recipes
|
#11
|
||||
|
||||
![]() Quote:
If I have the TOTEM Recharged with new frequencies, and is more stable, I'm just waiting for it to cook silver Jollas to 20 cm deep. Hope it works the experiment .... this frequency, change of capacitors, coils has me going crazy .. jajajajajajaj. If someone can provide me tx and rx frequencies, I'm infinitely grateful ... I can send the private message, Remember they are TOP SECRET- Si ya tengo el TOTEM Recharged con nuevas frecuencias, ya esta mas estable, solo estoy esperando que se cocine las jollas de plata a 20 cm de profundidad. Espero que funcione el experimento.... esto de las frecuencias, cambio de capacitores,bobinas me va ha volver loco ..jajajajajajaj. Si alguien me puede proporcionar las frecuencias tx y rx, se lo voy agradecer infinitamente...me las pueden mandar por mensaje privado, acuerdense que son TOP SECRET. |
#12
|
||||
|
||||
![]()
drtech; may be goldmaxx can help you whit any most right frecuences, i dont have build the totem due these totem lrl only are experimental prototipe and never show videos whit any succes, the rights recipes configurations for stabilizations of all lrl are the most dificultous of all these work , best regards dman
|
#13
|
||||
|
||||
![]()
drtech, my congratulations for you new lrl avatar
![]() |
#14
|
||||
|
||||
![]() Quote:
Hi what top secret dear friend??!!!!! Look here you can understand and find the exactly frequency and make modification http://www.longrangelocators.com/for...ad.php?t=18954 I always said I use 40 to 60 KHZ in my LRL's and work good http://www.longrangelocators.com/for...&postcount=102 http://www.longrangelocators.com/for...&postcount=107 http://www.longrangelocators.com/for...&postcount=110
__________________
God bless all - Nicolas << My channel >> << My shop >> Please do not demand Private Messages .... I cant reply all here....For more information you can send me email ....Thank you for understanding |
![]() |
Thread Tools | |
Display Modes | |
|
|