Mineralisation, el.field electromagnetic field problems

[Avanturis]

Hello everyone
I want to open a subject (maybe it's already been discussed) that's been troubleing some members and that's a subject about mineralisation, el.field, electromagnetic field. I made many dowsing rods with signal generator, and i always have a a problem with mineralisation elektromagnetic fields. Can someone make a suggestion or a solution to fix this. (Or is someone keeping that for themselves)

[Brahimolayt]

Hi my friends.sorry I don't practice dowsing but false electromagnetic interference and fort miniralisation is a problem for me to. Even radiology transmitters, engine sparks, fluorescent bulbs,high wire voltage and transformers ....ets make my device gives fals bips. I think its do to the Lc tank tuning of the receiver circuit or the external oscillator the question is in what frequency we must tune to.and dowsing rods is the same to.

[Mike(Mont)]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

[Avanturis]

Thanks Brahimolayt for your explanation

[Avanturis]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

Hello Mike
Thanks for for answer,but do you have experience with the Eliminator e 120, or signal generator with chip ICL8038.
I know the chip ICL 8038 not manufactured but its sold on Ebay ,Amazon AliExpress.

[Avanturis]

Your area might be problematic but you didn?t say your location. GDI-Detectors.com has a relatively inexpensive device Eliminator e120. You can use it as a signal generator then set it to filter mode to check target size. Just set the filter and circle the transmitter again to see if the target line is still there.

Thanks Brahimolayt for your explanation

[Mike(Mont)]

Hello Mike
Thanks for for answer,but do you have experience with the Eliminator e 120, or signal generator with chip ICL8038.
I know the chip ICL 8038 not manufactured but its sold on Ebay ,Amazon AliExpress.

Is this a history exam? The 555 timer more current. 8038 not very stable

[Avanturis]

Is this a history exam? The 555 timer more current. 8038 not very stable

Thanks for your reply
I have no knowledge of electronics and I want to research and learn from some who have many years of experience so I ask here on the forum to find out more about generators

[Mike(Mont)]

There are many electronics courses on-line. I understand you don?t want my advice so hope you get it figure out.

[Mike(Mont)]

Pretty good chance you are doing something wrong if you getting so many false signals.

Aim the rods down 15 degrees?that?s like about two inches down from level. Another one is lock time?how long the rods stay crossed when you stand on the target line.

Turn the power down

[Avanturis]

There are many electronics courses on-line. I understand you don?t want my advice so hope you get it figure out.

Mike, your advice is good

[Avanturis]

Pretty good chance you are doing something wrong if you getting so many false signals.

Aim the rods down 15 degrees?that?s like about two inches down from level. Another one is lock time?how long the rods stay crossed when you stand on the target line.

Turn the power down


You have a lot of experience and therefore I will accept any of your advice to learn.

[Mike(Mont)]

If your area is magnetic volcanic lava with flour gold I don?t know the answer, have no experience

But I do know using l-rods is the weak link in the chain. People don’t seem to realize you must keep your conscious mind out of way. Easier said than done. I pick an object out in front of me a ways and just look at it—even examine it—while using the rods. This is to distract your mind from trying to control things

[Avanturis]

Let me tell you how I reject electrostatic fields.
I throw some electrostatic or electromagnetic fields with a copper rod stuck in the ground and hold it with one hand and I have lrl in the other, but some are so strong that I have to dig the place to remove the ions, electron, protons from the earth or whatever.

[Mike(Mont)]

No locator works perfectly all the time. Yesterday afternoon I tried the e120 and the signal was very weak to non-existent. I do not have the l-rods amplifier

I went out in the yard just now and it was biting my test target. Solar activity was up yesterday but my experience is Summer sun
can be overpowering during daytime

My test target just a fresh drop on the surface

Low battery 7.3 volts

[Avanturis]

No locator works perfectly all the time. Yesterday afternoon I tried the e120 and the signal was very weak to non-existent. I do not have the l-rods amplifier

I went out in the yard just now and it was biting my test target. Solar activity was up yesterday but my experience is Summer sun
can be overpowering during daytime

My test target just a fresh drop on the surface

Low battery 7.3 volts

Mike, can you tell me which way it went around E 120?
L-rod amplifier made by yourself or you bought it, help me which amplifier to use

[Mike(Mont)]

I don?t have the l-rod amplifier. Gdi-detectors sells them, think they call it an L-rod Power Module

It’s in their Long Range Locator Kit

[Avanturis]

I don?t have the l-rod amplifier. Gdi-detectors sells them, think they call it an L-rod Power Module

It?s in their Long Range Locator Kit

Thanks again Mike ,I will see it on their website.

[Avanturis]

Hello Mike
Did you find anything with the Eliminator 120, like gold, silver, copper?

[Mike(Mont)]

I don?t remember. lol. I haven?t done any real hunting for quite a while.

If it has l-rods or swivel handle it can take huge amount of practice to learn.

[Avanturis]

I want to ask here on the forum whether the frequency from 0.1Hz to 20,000Hz if it passes through you as a conductor has a detrimental effect on health.

[Avanturis]

I don?t remember. lol. I haven?t done any real hunting for quite a while.

If it has l-rods or swivel handle it can take huge amount of practice to learn.

I understood Mike
I have been using my L Rod for about 10 years

[Mike(Mont)]

I want to ask here on the forum whether the frequency from 0.1Hz to 20,000Hz if it passes through you as a conductor has a detrimental effect on health.

?Go through you? is a bit ambiguous. I think you mean go through your skin? Big difference compared to current entering your body like through a small wound. But I think it is not a good idea to run a signal through the rod handle, and worse if it is an amplified signal, scalar waves the worst. Don?t mess with that even if just close contact.

[Avanturis]

https://www.longrangelocators.com/forums/attachment.php?attachmentid=20899&stc=1&d=1650809303

[Avanturis]

https://www.longrangelocators.com/forums/attachment.php?attachmentid=20899&stc=1&d=1650809303


Frequency sound generator is application for phone

[Mike(Mont)]

That?s not sound going through the wire

[Avanturis]

That?s not sound going through the wire

What is that??

[Mike(Mont)]

How?s that electronics course going?

[Mike(Mont)]

Anybody used the Gold x-finder? I see they just made an update. gdi-detectors.com

[Mike(Mont)]

When measuring target size, you really need to be close to the target for better accuracy. Del Winders said within 50 feet/ 20 meters. Longer distance gives exaggerated target size

[Mike(Mont)]

About electrical shock?One of Del Winders weight chek units gave someone a bad shock. It had a 555 timer circuit to provide a frequency that ran through the rods. He discontinued that one.

Just a micro hole in your skin can allow current to flow inside your body? that?s how people eat electrocuted. A micro hole can occur from a static electricity spark. Don?t be foolish and get yourself killed.

[Mike(Mont)]

I also should add that Del?s weight chek did not have an amplifier and still gave the guy a bad shock

[Mike(Mont)]

Also just can?t let this one slip by?This is not dowsing! The original MFD devices did not use any L-rods, just like the electronic receiver I?ve been working on. But you can use L-rods to trace the signal line-Del Winders figured this out. Usually I can find two signal lines that go to each edge of the target? s field. There is also a line right to the target but it not as easy to detect until you get up close.

[Avanturis]

Hi Mike, how are you?
It's been a long time since I haven't written here, I want to ask you and the other members of the forum, I'm just asking, i.e. I'm learning from you professionals
Have you used Spectra or Rayfinder from GDI from Greece, and is it worth investing in those locators or not?
Best regards

[Mike(Mont)]

Never used those but I have an Eliminator e-120 I like so I highly suspect the Spectra and Rayfinder are going to be better yet.

Many people afraid of L-rods but I am living proof to the fact anyone can learn LOL. Best way I have found is to pick out an object out in front of you a ways and look at it while you using the rods. The idea is to take your mind off the locating stuff— can’t be thinking about it. Keep your conscious mind out of it. Many people cannot do this

[Avanturis]

Never used those but I have an Eliminator e-120 I like so I highly suspect the Spectra and Rayfinder are going to be better yet.

Many people afraid of L-rods but I am living proof to the fact anyone can learn LOL. Best way I have found is to pick out an object out in front of you a ways and look at it while you using the rods. The idea is to take your mind off the locating stuff? can?t be thinking about it. Keep your conscious mind out of it. Many people cannot do this

Thanks again Mike for sharing your experience

[Mike(Mont)]

Another technique which is more like dowsing is to aim two L-rods straight in front of you and slowly do a sweep through the suspected target area. When you are aiming at the target the rods cross.

And another variation of this is to hold left thumb on top of rod so it doesn’t move. Right rod is free to move. Do a two-rod sweep while focusing your attention on the left rod. When the right rod starts to catch a target notice where the left rod is aiming. This takes practice to keep all you attention on the left rod. This one works pretty good.

[mustefa ubram]

Thanks for your reply
I have no knowledge of electronics and I want to research and learn from some who have many years of experience so I ask here on the forum to find out more about generators


Dear friend I suggest you to learn some electronic science first to understand the content better and easier.
To eliminate errors, you can use Eliminator-e120 or MES-x2 from Deep Finders.These two devices are designed to eliminate electromagnetic noise
G.L

[Mike(Mont)]

Looks interesting. Can't see the price.

[mustefa ubram]

Looks interesting. Can't see the price.
What is the price?

[Mike(Mont)]

How much does it cost?

[mustefa ubram]

How much does it cost?
You can get help from the company's support

[Mike(Mont)]

Doesn?t look like Deep Finders is still doing business. A bit strange they do not mention anything needing L-rods.

[Avanturis]

Dear friend I suggest you to learn some electronic science first to understand the content better and easier.
To eliminate errors, you can use Eliminator-e120 or MES-x2 from Deep Finders.These two devices are designed to eliminate electromagnetic noise
G.L

Hello
I appreciate your suggestion, thank you for your help me.