DDS Fuction Generator and rod dowsing

[apogonos]

construction for dowsing with generator COMPACT:D

http://s26.postimg.org/ycts2avqt/DSC01414.jpg (http://postimg.org/image/ycts2avqt/) http://s26.postimg.org/v9xnco65x/DSC01415.jpg (http://postimg.org/image/v9xnco65x/) http://s26.postimg.org/6j7yyuqt1/DSC01416.jpg (http://postimg.org/image/6j7yyuqt1/) http://s26.postimg.org/ed8kk8ylx/DSC01417.jpg (http://postimg.org/image/ed8kk8ylx/)

http://s26.postimg.org/gcp6bnsxh/DSC01419.jpg (http://postimg.org/image/gcp6bnsxh/) http://s26.postimg.org/nrei41et1/DSC01423.jpg (http://postimg.org/image/nrei41et1/) http://s26.postimg.org/gs0g4oeut/DSC01424.jpg (http://postimg.org/image/gs0g4oeut/)

[WM6]

Nice design. Congratulations.

Curious, what gold have to say on applied electronic science in dowsing rod?

[indiana jones]

Nice work Taki.:lol:

[Mike(Mont)]

Unfortunately the "hot dog on a stick" (frequency generator on a swivel handle) is not how a frequency generator is supposed to be used. You will do better if you place the device on the ground with antenna in the air and wait five minutes then circle it with an L-rod. Remember the signal line IS the discrimination. If you just use the sweep method it is unlikely you will get the signal line to develop.

[UltraLRL]

You will do better if you place the device on the ground with antenna in the air and wait five minutes then circle it with an L-rod.

It's Not The ONLY Way!!!

Always,There are a lots of ways to the solution.

[UltraLRL]

Nice Work apogonos

Did you build "AVR DDS signal generator V2.0" project??
http://www.scienceprog.com/avr-dds-signal-generator-v20/

http://www.electronics-lab.com/wp-content/uploads/2015/04/Photo_111.jpg


and about "ECG" function,I don't think ECG signal have any thing good for LRLs!
http://i2.wp.com/www.scienceprog.com/wp-content/uploads/2008i/DDS2/AVR_DDS_ECG.JPG

[WM6]

and about "ECG" function,I don't think ECG signal have any thing good for LRLs!



No doubt, but it is hard to survive useful information from ECG.

[Mike(Mont)]

It's Not The ONLY Way!!!

Always,There are a lots of ways to the solution.

Never said it was the only way, but it is the correct way and a better way. Even just holding the device in your left hand and using a bent coat hanger in your right hand as an L-rod is a better, more sensitive way--you can get a rod response when you walk past the target. But the real way is to walk across the discriminated signal line and you can't do that when you are holding the device. Don't take my word for it.

[apogonos]

Nice design. Congratulations.

Curious, what gold have to say on applied electronic science in dowsing rod?

Thanks,
electronic science = the dowsing rod :D

[apogonos]

Nice work Taki.:lol:

Thanks Xristo, ready for mountain?:razz:

[apogonos]

Nice Work apogonos

Did you build "AVR DDS signal generator V2.0" project??
http://www.scienceprog.com/avr-dds-signal-generator-v20/

http://www.electronics-lab.com/wp-content/uploads/2015/04/Photo_111.jpg


and about "ECG" function,I don't think ECG signal have any thing good for LRLs!
http://i2.wp.com/www.scienceprog.com/wp-content/uploads/2008i/DDS2/AVR_DDS_ECG.JPG


hi, Ultralrl

is not this circuit, there is a pic and an output circuit,
the signal in the antenna coil is in photo
19614

[UltraLRL]

The Output is going to be a square wave??
if so, you got Low Frequency Distortion
http://www.interfacebus.com/distrotion-low-frequency-square-wave.jpg

[reza vir]

Please take a film from sense of the metal

[sirnon]

Good job
Good luck bro