Antiphase spiral coil transmitter + receiver

[WM6]

For those interested in spiral coil transmitter here one simple transmitter schematic, which anti-phase frequency outputs can be set from down to 1Hz to up to 10MHz.

Transmitter frequency is set by C1 and C2, by rule:

C1 = C2

Par example

- to get frequency of 1Hz then C should be about 50uF
- to get frequency of 10MHz C should be about 10pF
- to get frequency of 1MHz C should be about 200pF etc.

Coil inductance of receiver should be calculated according transmitter set frequency.

Telescopic antennas are all connected over capacitors (TX with 47nF, RX with 47pF respectively).

IC1 of receiver is symmetric supplied by two 9v batteries.

http://i64.tinypic.com/286wen6.jpg

[detectoman]

wm6 thanks very much for schematic, i send a embrace from mexico, too at all group members

[WM6]

You are welcome detectoman.

Next weekend I will post proposal of one possible way of: how to build combined spiral/telescopic antenna (I am out of my home at the moment - till Thursday I suppose).

To clarify "tight" drawing: spiral antennas are connected between (Q1, Q2) emitters (respectively R6 of receiver) and ground. So this way representing by electrical symbol:

http://i68.tinypic.com/2rr17a8.jpg

Spiral coils inductance for 1MHz about 150uH.

Telescopic antenna can be replaced with piece of aluminum (or Cu) hard wire or small tube of adequate length for chosen frequency, par. example for 1MHz length is 150mm (not very critical).

Spiral antennas of TX (L1 and L2) are anti-phase wound, for zeroing (phasing for RX spiral antenna is of your choice - more will be explained latter with antenna build suggestion).

[abdou2014]

where is the rest of the circuit .

[WM6]

Rest of the circuit is in first post.

This (second) drawing only explain how telescopic and spiral antennas from first post schematic are connected (using electrical symbol for spiral antenna instead of, not so - regarding connectivity - clear first drawings).

I am trying to held complete circuit as much simple as possible, despite building and tuning spiral antennas is not completely simple. Power supply is left to builder choice and availability (74LS00 logic should be supplied in range of 4.75–5.25 V). If you use 5V regulator on 9V battery in TX stage, then you can supply transistors direct by 9V and IC1 over 5V regulator (in this case schematic supply lines should be adequate adapted: 9V at R6 and R5 instead of 5V).

As I already say in first post: RX IC uA741 should be supplied symmetrically by two 9V batteries according this there is mistake in schematic pin marking - instead of 0V at negative supply rail there should be -9V (please correct accordingly !!!!!).

[WM6]

A little theory on spiral coil magnetism to irritate mastermind:

http://www.sciencealert.com/a-magnetic-wormhole-that-connects-two-regions-of-space-has-been-created-for-the-first-time

[abdou2014]

there are not circuit . :nono:

[WM6]

there are not circuit . :nono:

So? Then you have serious problem. Take a big dowsing rod and hit your head at least 33x and you will see circuit suddenly.

[WM6]

Corrected (symmetrical supply for uA714) schematic:

http://i67.tinypic.com/2433spg.jpg

[Geo]

So? Then you have serious problem. Take a big dowsing rod and hit your head at least 33x and you will see circuit suddenly.

....................:lol::lol::lol:

[enjoykin4]

Привет WM6

Simplifay yours circuit - try this Scalar waves transmitter (longitudinal waves).
For the Scalar type receiver use the same coil as for transmitter. This device was known as "Tabletka Korobeinikova". :)

http://n-t.ru/tp/ts/nv4.gif

http://n-t.ru/tp/ts/nv2.jpg
White box is "Tabletka Korobeinikova".

Tr1 - any high frequency transistor with high ft= 100Mhz....1Ghz or upper - also with high h21e.

Др1 and Др2 are classical RF chokes. inductance of L1 = inductance of L2 . Two same coils with same wire diameter and same winding diameter but in opposite phase (180 degree) - one coil is righ wounded other left wounded/ adjust the distances between coils and tune resonant frquency. Driving with any shape signal on resonant fequency or on harmonics of resonant frequency. You can add two variabile (or fixed) capacitors in parallel with each coil for fine tunning together with searial capacitor C for blocking DC component and tuning resonant frequency of circuit.

link is:
http://n-t.ru/tp/ts/nv.htm

ps: antiphase coils were also known as "Partnered Coils" or "Bucking coils".

Best regards
enjoykin4

[Mike(Mont)]

WM6, is this a scalar transmitter? I don't understand its purpose. I guess it cancels out something. You have two opposite waves, then they go to zero. Must be very close to scalar but not quite the same?

[Mike(Mont)]

WM6, more questions. What does the conical-shaped spiral coil do compared to a flat spiral? I guess it concentrates the signal into a tighter pattern, or is it the opposite, a wider pattern? I look at it as each wall is pointing out towards the opposite side instead of straight ahead. I think I have been watching too much Alice in Wonderland--Through The Looking Glass. :lol: Please don't laugh too hard.

[WM6]

Hi enjoykin4, thanks for the nice proposal, how to test existence of Scalar waves.

We will come to this later in experiments.

For now: my proposal here is different from bucking coils in this that bucking coils are usually single phase driven and the turn anti-phase in coil construction. In my proposal two (single) coils are independent anti-phase driven.

In general: we need to balance here between long an very short wavelength.

At very short wavelength (say in cm of wavelength) devices constructed are very small and handy but all even minor parts used are very critical.

At longer wavelength (tens of meters or even kilometers) to get useful phase difference on directivity of reflected wave antennas should be bulky but electronic design is not critical.

[WM6]

WM6, is this a scalar transmitter? I don't understand its purpose. I guess it cancels out something. You have two opposite waves, then they go to zero. Must be very close to scalar but not quite the same?

WM6, more questions. What does the conical-shaped spiral coil do compared to a flat spiral? I guess it concentrates the signal into a tighter pattern, or is it the opposite, a wider pattern? I look at it as each wall is pointing out towards the opposite side instead of straight ahead. I think I have been watching too much Alice in Wonderland--Through The Looking Glass. :lol: Please don't laugh too hard.




Potentially yes, it could be converted to scalar transmitter. Main purpose in this design is to easily get quiet status in receiver or TX signal zeroing in receiver module.

Main drawback of Scalar waves is its advantage in same time. They cannot be stopped by material substance, so they cannot be reflected too. But they can trigger in some circumstances that parts of matter radiate their own Scalar waves. We live in world of waves and resonances. Depend of how we approach to this waves we can get mess of cacophony or pure music. There is no universal resonance in this world as resonance is main condition of identity all things in world of waves.

In fact proposed coils are not only conical spiral but logarithmic (not clear from drawing) wound conical spiral with phase shifted radiator in middle of spiral to get transverse longitudinal effect in antenna radiation. To proper phase shifting of middle radiator we need to select proper C on radiator supply line. This could greatly improve directivity of reflected wave on RX side.

[Mike(Mont)]

WM6, here's what I don't understand: To achieve resonance with the target, the transmitter and the target (receiver) must have same frequency but opposite phase. I don't see any way for the target to be in opposite phase because the transmitting coils are never going to allow this.

[Mike(Mont)]

Yes, I am interested in learning more about your coils. Actually i am trying to figure out how to get a wider pattern for the transmitter coil. i was thinking a reverse cone shape, so the point of the cone is facing forward.

[WM6]

I will post about practical coil design after return to my home, I am in another town at this moment.

In cases of reflective waves we do not need target to be resonance with TX or RX frequency.

For Scalar waves detecting, similar targets (similar coins, similar rings etc.) radiate at similar resonances. Here we need Scalar wave sources as trigger to put targets in higher amplitude of resonance and then relatively narrow-band receiver with enough directive Scalar antenna to catch at target resonance.

I don't know, particularly for coins or rings what could be its scalar resonance. This should be determinated experimentally. So step by step.

[Mike(Mont)]

Okay, thanks. Have a good trip.

[enjoykin4]

Hello WM6

If you have at your home or bussines very good equipped labaratory i can give you many useful informations which you can try in experiments.

Shortly - Scalar Waves are Nikolai Tesla Technology from 19th century. We now have theory and mathemathical apparatus by Proffesor Dr. Gennadiy V. Nikolaev and Dr Srefan Marinov.

All we need to do is to spend some money and spare time to experiments. This open new world outlook to Free Energy , Gold detection, Cosmic communications , Healing and many many more.


Dear WM6

Carefully read this newest article from january 2016 (7524 year) by Professor Tomilin (follower of Nikolai tesla and Professor Gennadiy V.Nikolaev)

http://electricaleather.com/d/358095/d/statya_15_11_2015_rus_eng.pdf

You have their emails so you can write them (on english) and talk about new Nikolaev electrodynamics and many newest problems in Scalar Physics.


This article is about:

Relationships between electromagnetic and mechanical Characteristics of electron

Tomilin A.K1, Misiucenko I.2, Vikulin V.C.3
1 National Research Tomsk Polytechnic University, Tomsk , Russian Federation
E-mail: aktomilin@gmail.com
2 Research Center "Algorithm" , St. Petersburg, Russian Federation
E-mail: ruberoid2101@yandex.ru
3 “High pass VLSI Laboratory “ Ltd, St. Petersburg , Russian Federation
E-mail: v_vikulin@mail.ru

A relationship between electron charge and electron mass was established based on energy relations. The obtained expression corresponds to relativistic transformation of mass. A conclusion was drawn about solely electromagnetic nature of mass. The authors take into account that vector potential of moving charged particle possesses two components – vortex components and potential component. Hence, the generalized magnetic field has vortex (vector) components and potential (scalar) component. It was also established that energy of potential magnetic field is negative and constitutes 1/3 of kinetic energy of particle. Besides, the well-known “problem 4/3” is solved successfully.
Keywords: mass, charge, field, electron radius, proton radius, physical vacuum, vector potential, generalized electrodynamics, energy of magnetic field, problem 4/3.

....

etc. etc.

reference.
Thus, the phenomenon of magnetic field itself proves the existence of physical vacuum. If one imagines a charged particle moving through absolute vacuum, it would be impossible to specify a factor that leads to distortion (described above) of the electric field of this particle. Of course, relativistic effect for a lone electron is manifested in accordance with (1), although in the case of charge-drift velocity of several millimeters per second, it is very small. Integral expression for this effect for the current in a conductor can only give an idea about the vortex magnetic field. Relativistic effect is incapable of describing the second component of the magnetic field – namely, potential component.

Conclusions:
....

4. Magnetic field emerges in the course of charged particle motion relative to vacuum medium.

5. Magnetic field of a lone charge has two components – vortex (vector) component and potential (scalar) component.

6. Energy of scalar magnetic field has negative sign.

etc.etc....

Fisrt part on Russian second on English.

Best regards :)
Enjoykin4

[enjoykin4]

Some hints for all !!

Vector potential A→ of moving charged particle possesses two components – (vector) vortex components and (scalar) potential component.

Look at our planet Midgard Earth as moving charged particle (from point of view for example our galaxy or universe).

Direction of vortex (vector →) component is from EAST to WEST.

Scalar component has no direction - it is gradient of vector potential and has minus sign. It means - it is a kind of real negative energy (not negative vector but new kind of energy substance) which manifest yourself radially through center of the planet - inner core of the planet radially

If we call for example current of transverse (vector) EM wave "HOT CURRENT" - current of longitudinal (scalar) EM wave will be "COLD CURRENT" because it cold conductors while running through it.

Vector potential is a REAL FIELD of our planet and not only our planet. Every charged particle has vector potential. it is a kind of own force field like for example aura in human beings, etc....

Best regards
enjoykin4

[WM6]

Thanks enjoykin for all of info's. A lot to read.

Primary I am interested in simple experiments, no matter if they are based on simple or sophisticated theory.

I am not a scientist and this way not interested in argue with scientist about some theories.

If theories has its real basis, then they can be proven in simple way. I mean this as in a way you proposed with experiment "Tabletka Korobeinikova". I have enough well equipped electronic lab to carry out such simple experiments in frequency or time domain (btw. I am retired person now and can dedicate my time for my hobbies).

According this and considering your last info's, I am interested in simple experiments that can prove this claim:

"current of longitudinal (scalar) EM wave will be "COLD CURRENT" because it cold conductors while running through it."

Did you spotted somewhere info about simple experiments that can prove this claim?

[Mike(Mont)]

Enjoy4kin, (just figured that one out. :lol:) There is a book published in 1975 called "Supersensonics" by Christopher Hills. drhills.com website is not up and running but you can email them. Hills talks about what he calls "proticity". Where electricity uses electrons, proticity uses protons. He talks about the East-West flow as another type of polarity. He says it is more powerful than north-south polarity. As I recall he said it is not magnetic. Pretty sure he said this is what the ancient Egyptian dowsers used. I'll have to go back and read it again, but it certainly sounds like the same thing you are referring to here.

Glad to see you have an interest in this subject.

[enjoykin4]

Hi WM6

Nikolai Tsla experiments with RADIANT are key to Scalar electrodynamics - but keep in mind that there are not "a simple" - in sense of understanding real physical interactions in Scalar physics. This is because lack of knowledge and awareness in this field.

Also make experiments with Brovin's Katcher - small radiant transmitter on semiconductors.

Best regards
enjoykin4

[enjoykin4]

Enjoy4kin, (just figured that one out. :lol:) There is a book published in 1975 called "Supersensonics" by Christopher Hills. drhills.com website is not up and running but you can email them. Hills talks about what he calls "proticity". Where electricity uses electrons, proticity uses protons. He talks about the East-West flow as another type of polarity. He says it is more powerful than north-south polarity. As I recall he said it is not magnetic. Pretty sure he said this is what the ancient Egyptian dowsers used. I'll have to go back and read it again, but it certainly sounds like the same thing you are referring to here.

Glad to see you have an interest in this subject.


Thank you Mile(Mont) for information about "Supersensonics".!! :)

Can you upload "Supersensonics" book if you have it in some document format like pdf, doc...etc.?

About Vector potential A→ or simple Eeast-West-Flow. In Russia at some hidden place in very deep forest still today exist Miighty Scalar power station made by 3 physicists soon after second WW. Power station is still working but had not been used for a quite long time after those 3 physicists have been shoot by Jewish Zionist-Communist party as "Public enimies (of Jewish nation)".

Power station take a power directly from the earth ground. It is the only one working Free electricity scalar power station in the wrold today.


Reconstruction of Scalar power station - from the story of the forester :

Quote forester:

"I have carefully considered power- station — It is a metalic pipe with a diameter of 50 mm with the length 80 meters. There was no magnet near at hand that to check, but in my opinion a stainless steel. The pipe keeps on columns (insulators) material is similar to textolite height from the earth about 1m. Coils (metalic springs) are welded on upon a metalic pipe probably made from the same material as a pipe (I determined by color visually). Coils (metalic springs) are welded on through equal distance approximately 2 meters, length of coil (spring) too identical (coil) is about a 1 meter. On the end of a pipe the scrap is welded on — according to stories of the forester it is a copper to check I didn't become closer than meter to approach. I didn't decide.

The second end of a pipe is grounded (goes to the earth), according to the story of the forester the pipe is simply hammered into the earth of meter on 1.5 on 2."


Best regards
Enjoykin4

[enjoykin4]

Enjoy4kin, (just figured that one out. :lol:) There is a book published in 1975 called "Supersensonics" by Christopher Hills. drhills.com website is not up and running but you can email them. Hills talks about what he calls "proticity". Where electricity uses electrons, proticity uses protons. He talks about the East-West flow as another type of polarity. He says it is more powerful than north-south polarity. As I recall he said it is not magnetic. Pretty sure he said this is what the ancient Egyptian dowsers used. I'll have to go back and read it again, but it certainly sounds like the same thing you are referring to here.

Glad to see you have an interest in this subject.


Thank you Mile(Mont) for information about "Supersensonics".!! :)

Can you upload "Supersensonics" book if you have it in some document format like pdf, doc...etc.?

About Vector potential A→ or simple Eeast-West-Flow. In Russia at some hidden place in very deep forest still today exist Miighty Scalar power station made by 3 physicists soon after second WW. Power station is still working but had not been used for a quite long time after those 3 physicists have been shoot by Jewish Zionist-Communist party as "Public enimies (of Jewish nation)".

Power station take a power directly from the earth ground. It is the only one working Free electricity scalar power station in the world today.


Reconstruction of Scalar power station - from the story of the forester !!

Quote forester:

"I have carefully considered power- station — It is a metalic pipe with a diameter of 50 mm with the length 80 meters. There was no magnet near at hand that to check, but in my opinion a stainless steel. The pipe keeps on columns (insulators) material is similar to textolite height from the earth about 1m. Coils (metalic springs) are welded on upon a metalic pipe probably made from the same material as a pipe (I determined by color visually). Coils (metalic springs) are welded on through equal distance approximately 2 meters, length of coil (spring) too identical (coil) is about a 1 meter. On the end of a pipe the scrap is welded on — according to stories of the forester it is a copper to check I didn't become closer than meter to approach. I didn't decide.

The second end of a pipe is grounded (goes to the earth), according to the story of the forester the pipe is simply hammered into the earth of meter on 1.5 on 2."


Best regards
Enjoykin4

[Mike(Mont)]

drhills.com still sells the book. Last I saw about $35. There is not very much info about proticity in the book but there is much info on dowsing. One of my favorite books.

[enjoykin4]

Than you Mike(mon)

I am looking more additional info about "proticity" not for dowsing. !!:)


My opinion about work of scalar power station:

Our earth is surrounded not with a magnetic field, but with electric, which extend and manifest to three directions.

Standing electric waves form North-South Flow and East-West flow make "energetic lattice (grid)" of all our planetary space (inner and outer) — all the matter is stabilized and synchronized by means of this electric lattices (grids) - including biological entities.

Standing waves have zones of the greatest and the smallest values of potential (nodes and anti-nodes), still call them Hartman's grid or Hartman's lattice.

And so, if it is correct to find exact position of this electric lattice (grid) and to arrange in places of nodes and anti-nodes strong difference electrodes, it is possible to get the electric power directly from the Hartman's lattice by making Scalar power station in essence longitudinal waveguide (converter).


To do this we need to make very simple and very complex (in sence of understanding the clue) device known now as Shalatov's dynamic magnetometer.

We are looking for "Electiric ghosts or Scalar Phantoms" !! :)

Best regards

[enjoykin4]

http://www.overunityresearch.com/index.php?action=dlattach;topic=2470.0;attach=2105 1;image

Mike(Mont) if you are interesting search and download documents which Smudge has posted at http://www.overunityresearch.com/index.php?board=186.0

Creating electron current by moving magnetic field gradients (in essence gradient of Vecotr potential A→) :)
http://www.overunityresearch.com/index.php?topic=2925.0

Best regards
Enjoykin4

[enjoykin4]

Than you Mike(Mont)

I am looking more additional info about "proticity" not for dowsing. !!:)


My opinion about work of scalar power station:

Our earth is surrounded not with a magnetic field, but with electric, which extend and manifest to three directions. Standing electric waves form North-South Flow and East-West flow make "energetic lattice (grid)" of all our planetary space (inner and outer) — all the matter is stabilized and synchronized by means of this electric lattices (grids) - including biological entities. Standing waves have zones of the greatest and the smallest values of potential (nodes and anti-nodes), still call them Hartman's grid or Hartman's lattice. And so, if it is correct to find exact position of this electric lattice (grid) and to arrange in places of nodes and anti-nodes strong difference electrodes, it is possible to get the electric power directly from the Hartman's lattice by making Scalar power station in essence longitudinal waveguide (converter).

To do this we need to make very simple and very complex (in sense of understanding the clue) device known now as Shalatov's dynamic magnetometer.

We are looking for "Electiric ghosts or Scalar Phantoms" which are real !! :)

Best regards

[Mike(Mont)]

Proticty and dowsing are intertwined. You use the dowsing or Supersensonics to study the proticity. Hills was not being very Politically Correct when he said something like: Second hand knowledge on the subject is like reason to a mindless fool.

[enjoykin4]

Yes I agree with you Mike(Mont).

Power source of "Proticty" is a Human mind (not biological structure knwn as a Brain".
Our thoughts are flows of Proticity.

Mind is multidimensional energetic structure. :)

DNA and RNA spirals are also multidimensional energetic structure and all these structures also our bodies were made in unique Naturaly proportion - Golden proportion of fi and 1/fi. fi=1,6180339887498948482045868343656......

[Mike(Mont)]

Yeah, well don't confuse it with the psychic stuff. Here's an example: Say you have a forked stick and you found an underground water source. Now you walk away from the spot until you get another rod response. This distance is equal to the depth of the water. Now if you were going to do it psychically, you would just stand there and count the number of feet (or meters) until you get a response. There is a big difference here in accuracy.

[WM6]

Here one possible practical construction of Spiral logarithmic antenna.
I am taking hard paper for antenna body.
It can be out of hard foil, conical plastic tube, polystyrene or wood too.

My dimensions are to suit to RX antenna EM shielding container.
There can be other dimensions too.
More pictorial:

http://i68.tinypic.com/aw5ik6.jpg

http://i68.tinypic.com/10of9qe.jpg

http://i67.tinypic.com/242iovt.jpg

http://i67.tinypic.com/14e3wvm.jpg

[Mike(Mont)]

WM6, thanks for the info. Is each set of turns connected to the next in series?

[WM6]

Yes turns sets are serial connected - this way:

http://i68.tinypic.com/2wqzuwp.jpg

[Mike(Mont)]

Okay, Thanks WM6. Looks good.

[WM6]

Such yarn cones from yarn mill in textile manufacturing could be very practical body for spiral conical antenna:

http://i67.tinypic.com/242hi0p.jpg

[Mike(Mont)]

WM6, thanks. You gave me some good ideas to work on. Basically I need something flatter and inverse for a transmitter coil that has a wider pattern. I have my doubts this will work with the lower frequencies but i plan to jump in the deep water and see if I can swim. :lol:

[iron1944]

WM6
Grand Masters.
This has to be done in the same box assembly TX and RX?
Or held on the separation assembly?
thank you.

[WM6]

This has to be done in the same box assembly TX and RX?
Or held on the separation assembly?


Hi iron1944

It is almost impossible to zero-tune device if TX and RX are in the same housing.

RX part should be magnetically shielded too - not RF shielded only.

Conserve (dog) can is very cheap and effective shield for such purposes.

So, RX part inclusive RX antenna should be canned this way:

http://i66.tinypic.com/300cumd.jpg

Whole device should be constructed this way:

http://i64.tinypic.com/nzlt03.jpg

[Mike(Mont)]

I'd tell everyone to put out your B.S. deflectors on this one. Those coils are pretty close to what is called a phased array. That's for microwave frequencies, not going to work for treasure hunting in the ground. Like I said in a previous post, this does not appear to be scalar wave generator. And the biggest tell is the guy won't even build one himself. What is that about? No confidence in his own hand. :nono: This looks right along the same lines as that calculator hoax. Maybe even the same guy.

[WM6]

You should not mix electromagnetic radiation with radiation structure for a (quasi static) vector and scalar signal potential. Last one radiated at common axis (zeroing plane) of capacitive and inductive vectorial planes which are opposite to each other.

Transmitter schematic is OK and can be used as anti-phase current (for inductive component of antenna) and voltage (for capacitive component of coil) source.

First proposed antennas (as I previous say) was not intended for scalar wave generation, cause inductive and capacitive components are not separated enough in such array to be tuned for zeroing independently. So for scalar wave generating TX antenna radiator should be reconstructed and simplified. But proposed anti-phase electronic circuit is proper, simple, reliable and effective.

Basic scalar wave generation radiator (TX scalar antenna) should look like this:

http://i66.tinypic.com/rtok12.jpg


Tuning (zeroing) here mean to tune at maximal suppressed (nulled) electromagnetic field
in horizontal (forward) plane of this vector scalar radiator. This at the same time mean
achieving maximum at scalar and vector potential at the same horizontal plane.

Transmitter circuit can be incorporated (including battery) in middle radiator tube.