Lrl from Italy

[tanrila]

thanks master franco with best regard for you

[FrancoItaly]

Hi detectoman,
I can not send you a private message:
"detectoman has exceeded their stored private messages quota and cannot accept further messages until they clear some space."
Regards

[detectoman]

jjaja ok franco, i see fix these, regards :)

[brs]

hi franco
VU meters using
I want to be linked to lrl quartz version
Where you can connect and link IC1A , IC1B , IC2A or IC2B

[brs]

TR1 5V
TR2 0V
TR3 1,1V
TR4 1,2V
TR5 4,57V
PIN 1 IC1 0, 800V and
Increases with voltage lighting gradually
---------------------
PIN 7 IC1 10.58V
And IC2 10.63V
With the lighting voltage is reduced without gradually to 1v

[FrancoItaly]

First unplug the oscillator disconneecting C2, the voltage of TR2-TR3-TR4 collectors have to be in the range 3 - 5V, to increase the collector voltage should increase the resistance between collector and base and vice versa.
For TR5 emitter 4.57V is ok. You can connect the VU meter at PIN 1 of IC1 with the calculated resistance suitable for 11 volt full scale. IC2 is not necessary and you can use IC1B for buzzer.
Regards

[brs]

thank you Mr franco

[brs]

hi franco
bc183c Alternative bc550c

[FrancoItaly]

Yes it's ok

[darkman]

any Professional one here try any thing with new sensor stage ?:|

[FrancoItaly]

The new sensor stage, self oscillation type, it's very critical and unstable and I do not recommend. Instead I have modified the Lrl with CD4046 and I lowered the frequency to about 59 Khz (gold frequency?) It's very stable but I have not tested on real field. I used a ferrite coil with 200 turns (1.8 mH). If the lrl is ok on the field I will post the circuit diagram.

[FrancoItaly]

I just got back from the test field , unfortunately no signal from silver coins and a gold bracelet buried for over a year, so my ferrite coil LRL is not working.

[brs]

Thank Franco
If quartz device best

[brs]

Battery and handle hand must be far away from the circle PCB

[Geo]

I just got back from the test field , unfortunately no signal from silver coins and a gold bracelet buried for over a year, so my ferrite coil LRL is not working.

Bad news but no problem, you have so many workable versions.
Hello Franko, continue your fantastic work.
:)

[FrancoItaly]

Hi Geo,
Thanks for the compliments, there is still a chance for the ferrite coil LRL, in fact I had no connected the stylus antenna, now I have done but I can not go in the test field, too hot and too many mosquitoes.
Best Regards

[iam_7up_gamer]

Hi franco , how are you ?
That is bad news .

[FrancoItaly]

I'm fine but I will return soon to Switzerland and will not return until a few months. The tests will be for autumn.
Regards

[detectoman]

hello lrl builders brothers here i show yours my new lrl prototipe 2015 this is in aware of tries and news possible implementations i gave special thanks to my friend FrancoItaly for iniciate us in these actual projects a embrace for you and for all, gun semms succesfull here i need try in fields but havent gold buried but 20 coper coins https://www.youtube.com/watch?v=5RDRbJEnQwg&feature=youtu.be

[detectoman]

a strange lrl whit capability for detect all class metal near the antens also static plastic
https://www.youtube.com/watch?v=53IfrD71J7w&feature=youtu.be

[brs]

Mr. Franco
Do the phenomenon(Electromagnetic energy) of all-metal buried until flattened iron manufactured phenomenon

[FrancoItaly]

I must say that not much is known of the phenomenon, but I'm sure the iron is not detected, any form has.

[brs]

Thank Franco
worked on the assembly of a new quartz device and the work I have 2 silver ring at a depth of 40 cm was discovered phenomenon of almost antenna Pen distance 1.5 meter and be prompt on the place also discovered from the north to the south only

[FrancoItaly]

You say that you have detected 2 silver ring at 1.5 meters in north south direction?

[brs]

Yes almost 1.5 meters depth of 40 cm length of 9 months and buried detected from north to south and only weak from east to west

[FrancoItaly]

I think it's a good result similar to the one I got with 5 silver coins buried at 25 cm.
Probably gold is detected to greater distance.

[ouiarabe]

I decided to change my LRL and run at 59Khz (gold frequency) but at the time I am away from home and I can not test it. In practice it is a species of regenerative receiver, but the oscillation is continuous, even without signal at the input. To achieve this a part of the signal, using 4.7K trimmer and 100pF capacitor, it is send to the coil. For the coil we may use about 100 turns and we have to choose the right value for the capacitor placed in parallel to the coil. The emitter capacitors of the second and third transistor they set the stage gain of each transistor and the value must be determined experimentally. I repeat that I have not made this change, and I hope that some of you have wanted to do it.
Best Regards

hi all
thank you sir Francoitaly
for your help and cooperation
just a question please
what is the value of both capacity

[FrancoItaly]

This version for me doesn't work, however you can try 1 nF for both and increase until you have 2-5Volt (DC output).

[FrancoItaly]

I have received requests to repost scheme of my lrl. It's the 8Mhz quartz version. Power-display(1 led) is the stabilized supply with led alert of low battery and 1 led for display. Display(3 led) is the scheme for 3 display leds but it is always necessary stabilized power supply.

[ouiarabe]

thank you very much Franco
I will build this device and keep you informed of the results

[taxma1981]

how to place a crystal and an antenna Frank; I want to make something similar to your own design, the crystal will go in front but what values of capacitors and resistors; and who will enter the antenna after the 2n4416

http://s30.postimg.org/3xti50zbh/aaaaa.jpg (http://postimg.org/image/3xti50zbh/)

[FrancoItaly]

Sorry but I don't well undestand what you mean, in the past I tried other solutions for my lrl but this is the better, there is a lot of amplification and some change may cause autooscillation . I don't like FET transistor and the base of the first transistor for me is the better point for the antenna, I suppose that the base-emitter junction is important for phenomenon detection.
Regards

[taxma1981]

I mean the plan that I put.who i connect the antenna and the crystal?

[FrancoItaly]

I don't know, this is not my design, that comes from a modified rf sniffer, if you change transistors and schematic I cannot say nothing else.
Regards

[taxma1981]

I know that it is not the plan you simply request an aid for another ... you know about this

[humhum]

Design from Morgan or Who ?????? :D :lol:

[taxma1981]

Design from Morgan or Who ?????? :D :lol:

Nein :lol:
http://s29.postimg.org/ht7le88cz/20150919_233642.jpg (http://postimg.org/image/ht7le88cz/)

[Geo]

Taxma, open a new thread, don't destroy the thread of Franco!!!!

[FrancoItaly]

Hi Geo,
How are you? I have already said privately taxma, his lrl is broadly similar to my LRL, but, as you say, it is better to test on the field my LRL and it's for this reason I posted my LRL on the forum. I already had privately confirmed the good functioning of my LRL and invite again all those who have had success to reveal it publicly on the forum.
Regards

[RS_Phil]

I have received requests to repost scheme of my lrl. It's the 8Mhz quartz version. Power-display(1 led) is the stabilized supply with led alert of low battery and 1 led for display. Display(3 led) is the scheme for 3 display leds but it is always necessary stabilized power supply.
BC183 is hard to find here in my near electronic store can I replace this transistor of the same type?

Regards Saromines_R

[taxma1981]

with bc 547c work fine

[taxma1981]

I need antenna and ist ok

http://s11.postimg.org/t4pxv184v/20150923_204748.jpg (http://postimg.org/image/t4pxv184v/)
http://s13.postimg.org/dykndyq4j/20150923_204650.jpg (http://postimg.org/image/dykndyq4j/)

[taxma1981]

https://youtu.be/uCezifFu8Ss

[taxma1981]

Detect microwave why?

http://s8.postimg.org/byipa3ry9/20150922_211558.jpg (http://postimg.org/image/byipa3ry9/)


https://youtu.be/vAr6ByPwkn0

[FrancoItaly]

The resonant circuit connected to the antenna is in the range 100-150Mhz and sources of radio frequency which falls in this range (also with sub harmonics) affect the LRL especially if they are very close and in the house there are many sources of this kind. We can use these sources to test our LRL but my favorite test it's to touch the antenna and check the signal decreases, to do this set the threshold so that the LED is turned on weakly then by touching the antenna the led should go off.
Regards

[taxma1981]

I did this when handling the antenna, the voltage drops .. Detects static Yesterday rubbed the comb in the hair of 4 meters and started beating

[taxma1981]

how crystal is working better franko ?we can be put and largest;

[FrancoItaly]

If you mean the size of quartz, small size is equal to normal size. The frequency is no critic, I have used 4 - 6 - 8 and 10Mhz with no difference.

[taxma1981]

Frank 4-6 volts must have; measuring the exit to ground; so why zero .... 4-6 volts only shows measuring the exit and entrance front

[FrancoItaly]

I don't understand what you mean with "zero", the DC output of sensor stage, that's the rectified AC signal, it must be in the range 2-6V.

[FrancoItaly]

For Saromines_R and for others who have asked for my help.
if on the emitter of TR5 there is a voltage equal to or greater than 7V:

1)- remove C2, C3 and C4 and measure voltage again, it is still higher than 7V, decrease the value of C13 (from 560pF to 470pF or 330pF) if not enough reduce also C14. Reconnect C2, C3 and C4, if the output is between 2 and 6V LRL is ok but if it is still high, go to point 2:

2)- Try for C2 0.5pF or less

3)- remove C2, C3 and C4 and try the connection with two wires which it is equivalent to a capacitor of very low capacity. You can also twist the two wires to vary the capacity.

4)- try the connection with one wire which it is equivalent to a little antenna, start with a length of 10cm and try different solutions, passing near the base of TR2 and possibly shortening if the voltage is still too high.

I hope this can help, if you can not get the right voltage then you need to redesign a new pcb, preferably double-sided with one side connected to ground.

[taxma1981]

here measured Franco; the exit of the way 5, and in front of the entrance of TP1;
http://s13.postimg.org/f5yohepur/20150928_001544.jpg (http://postimg.org/image/f5yohepur/)

[FrancoItaly]

I don't understand, what is TP1, transistor TR1? What 's the voltage at TR5 emitter? If you have 2 - 6V and when you touch the antenna the voltage drops it's all OK.

[taxma1981]

the proposal does not fall Touching the antenna.

[RS_Phil]

Thanks sir Franco...

[brs]

TR4 = 6.37V voltage value, and if you connect the antenna increases the voltage
TR5 = 6.65V

[FrancoItaly]

Collector voltage of TR4 is better about 5V , change the 1M resistance base-collector to 820K or 680K or collector resistance from 4.7K to 5.6K. Emitter voltage of TR5 must be less than 6V. The lrl is very sensitive to the proximity of the human body and the important thing is that there be variations touching the antenna. However, it is crucial the field test. It is also important that the handle is long enough to keep the body away from the LRL, I think that is a fair measure 25cm.

[brs]

thank you mr.franco

[RS_Phil]

May TR5 V out is more than 5V only twisted magnetic wire i used on C2 C3 C4..if I disconnect the wire i measure more than 2V..one problem I have is a poor sound on my buzzer or cracking audio..i used 12v buzzer,..any suggestion master franco? by the way when i touched the wire or pass to the other transistor like Q2 or Q3 the led turning OFF is it the indication that my board is working correctly?

Best regards

Saromines_R

[FrancoItaly]

You can disconnect the wire because it is not necessary because it is sufficient the only parasitic capacitance. If you touch the antenna and the led goes off the lrl is ok. I think that you must change the buzzer, some types sound stronger than others while working with the same voltage, or You can put the buzzer outside the box.
Regards

[brs]

Mr. Franco
put the shield connected to the negative pole 12v- and when I rounded the hand of the resistance is affected by the changing

[RS_Phil]

You can disconnect the wire because it is not necessary because it is sufficient the only parasitic capacitance. If you touch the antenna and the led goes off the lrl is ok. I think that you must change the buzzer, some types sound stronger than others while working with the same voltage, or You can put the buzzer outside the box.
Regards

Ok master franco thanks for advise

[abdou2014]

HI Mr FRANCO I WOULD LIKE TO ASK YOU ABOUT DUAL ANTENNA
HANDHELD AND STYLUS IN ONE . I THINK THIS METHOD IS USED TO CREATE A MAGNETIC FIELD WITH THE STYLUS ANTENNE TO KEEP AWAY THE POSITIVE ION FROM THE INTERRIOR ANTENNE . AND DETECT ONLY THE NEGATIVE ION . IF MY THEORY IS TRUE PLEASE SHOW ME HOW IS MADE THIS ANTENNE

[FrancoItaly]

I do not understand what you mean, in my opinion is the best single antenna, also not sure that the ions are part of the phenomenon, also ions require a large input impedance, and is certainly not the case with my LRL. First of all realize my LRL and verify its operation and after you think about changes.
Regards

[abdou2014]

I BUILT ALL VERSION OF YOUR LRL . WHEN I PUT MY HAND NEAR THE ANTENNA THE LED LIGHTS. IT IS VERY SENSITIVE. IT CAN DETECT THE STATIC CHARGE OF THE HUMAN BODY.AND ALSO ELECTRONIC DEVICE FROM A LONG DISTANCE. WHAT DO YOU SAY ABOUT THIS RESULT . GOOD OR FALSE ?

[FrancoItaly]

Yes this is ok,my LRL is sensitive (like other instruments of this kind) to magnetic or electrical noise source.
Regards

[abdou2014]

Thank you Mr Franco. And what follows from this work. to cancel the electricity and magnetic fields earth ?

[FrancoItaly]

The LRL is used outdoors, where there is no interference. The LRLs are unusable close to every kind of transmitters.

[gwlwudi]

hi,FrancoItaly

I made you 8mhz sensor stage circuit, however, crystal oscillator can not afford earthquake. Then I simulate the circuit, remains the same, is not crystal to crystal active it?

Thanks !http://image.baidu.com/detail/newindex?col=&tag=&pn=0&pid=28827379574&aid=410700831&user_id=865971622&setid=-1&sort=0&newsPn=&star=&fr=&from=2

[FrancoItaly]

Look at my post n.552, crystal oscillator must be active, TR2, TR3 and TR4 amplify a small part of the signal coming from the oscillator. If disconnects the Quartz there should be no output.

[LRLMAN]

Look at my post n.552, crystal oscillator must be active, TR2, TR3 and TR4 amplify a small part of the signal coming from the oscillator. If disconnects the Quartz there should be no output.

Hello dear Franco could you show the pcb with which you made the sensor 8 MHz and the other stages such as the display and all this as the image of the post 282, wich i analyze and compare it with the image of the PCB in post No. 213 and no seems with the image of the post 282, please could you show us the pcb like as in post 282?

Receive greetings and thanks for sharing your project, excellent.

LRLMAN

[FrancoItaly]

Hi LRLMAN,
unfortunately not in Italy, maybe you're right, the PCB are not the same, I did more than 10 lrls, however all the PCB are working, you should look at the wiring diagram when you make mounting the components on the PCB. Watch "My new FrancoItaly LRL" where there is the full realization of Sneshko: "http://www.longrangelocators.com/forums/showthread.php?t=19076"
that did a really good job. However the important thing is to try to avoid the auto-oscillations, as TR2, TR3 and TR4 are a high gain stage, it's better a pcb not too small, maybe double-sided with one side connected to ground.
Best Regards

[LRLMAN]

Hi LRLMAN,
unfortunately not in Italy, maybe you're right, the PCB are not the same, I did more than 10 lrls, however all the PCB are working, you should look at the wiring diagram when you make mounting the components on the PCB. Watch "My new FrancoItaly LRL" where there is the full realization of Sneshko: "http://www.longrangelocators.com/forums/showthread.php?t=19076"
that did a really good job. However the important thing is to try to avoid the auto-oscillations, as TR2, TR3 and TR4 are a high gain stage, it's better a pcb not too small, maybe double-sided with one side connected to ground.
Best Regards

Hello Franco in advance thank you very much, only i commented that I interesting to do your project but with PCBs that you made and I would like to ask if you can put an image of the face below the sensor (8 mhz) to see how this your connection to ground you say, and image how you connected the antenna and the antenna as it should be because I have a television antenna but do not know if this type of antenna used for the project or only i have to use only the RF radio type with metal tip?.

I say I want to see pictures of your PCB because I think they are better such as do the Teacher Alonso.

It's something I do not understand but that making the PCB's so as make Alonso, the LRL work well.

You would have some difficulty in putting images of your PCBs? when you come back to Italy? if you have your lrl in Italy.

Also I would ask the inductance of the coil L1 and the diameter of the wire, because I made several coils of different sizes as you said to Nicolas, which should be 10 mm x 10 mm and I can't get the inductance you told to Nicolas that was less than 1 uH, I measure the inductance and only get 1.5 uH minimum and not less with 1 mm wire diameter.

Best Regards.

Lrlman

[FrancoItaly]

Hi LRLMAN,
unfortunately I do not know when I return to Italy as part of my life is spent here in Switzerland with my wife who is not in good health.
You speak of the Teacher Alonso, but Alonso has nothing to do with my LRL that originated from an RF sniffer that's autooscillates and acted as a LRL.
For the moment the only pcb I can show you is on the forum but you can experiment with other pcb. Even the antenna is not critical, okay a stylus antenna or a tube of copper or brass from 30 to 40cm long. L1 also is not critical, diameter of wire is about 1mm, 10 x 10mm with 3 turns it's ok, also 2 turns work well and the inductance is not important, my instrument is not very accurate.
Best Regards

[enjoykin4]

ПРИВЕТ ВСЕМ НА ФОРУМЕ !! :)

Hello FrancoItaly and all LRL team/s at this forum and around the world. :)

This is my first post here. Thanks Carl and Qiaozhi from geotech.

Franco - I was reading whole your thread and have got a strong desire to replicate all of your LRL lasers (PD).

Franco would you be nice and friendly and public all yours PCB's and components layout for your last 4th builds.

version 1 - self-oscillating version using both sidee pcb epoxy as parasitic capacitor. I need both sides in 1:1 ratio.

version 2 - as is from PICT0751.jpg. I only need right dimensions in mm for pcb so i can adjust aspect ratio for 600dpi laser printing.

version 3 - with PLL 4060. I have schematic but need your original pcb layout and silkscreen.

version 4 - quartz lrl at 8MHz. Also i have schematic but no pcb and silkscreen.


FrancoItaly - if you are interesting i think i knew a answer on mystical phenomenon you have caught. Taking in account my older anomalies research in that area of physics (i really like nature "anomalies") i knew 100% that phenomenon really exist and have natural source just like a universe surrounding us. Also phenomenon is exellent masked but not intentionally from anybody will at universe or wider (in other universes). The point is as a matter of fact in very complex organization on nature hierarchy , which possess multlevels fractal anisotropy as primary building structures for different spatial dimensionality. Very shortly answer for mystical phenomenon is The Second Magnetic Field H* = - div A, (A is vector potential) and his non-electrical properties on physical density matter.

ps: Quote D'Arsonval:
«Anything is possible. But one must not accept anything , except that which can be experimentally proved. The ideas of an insane person differs from the conceptions of a genious , mainly because experiment invalidates the former and confirms the latter.»


That's all for now.
I wish good luck to all in gold hunting.

Reg,
Enjoykin4

[LRLMAN]

Hi LRLMAN,
unfortunately I do not know when I return to Italy as part of my life is spent here in Switzerland with my wife who is not in good health.
You speak of the Teacher Alonso, but Alonso has nothing to do with my LRL that originated from an RF sniffer that's autooscillates and acted as a LRL.
For the moment the only pcb I can show you is on the forum but you can experiment with other pcb. Even the antenna is not critical, okay a stylus antenna or a tube of copper or brass from 30 to 40cm long. L1 also is not critical, diameter of wire is about 1mm, 10 x 10mm with 3 turns it's ok, also 2 turns work well and the inductance is not important, my instrument is not very accurate.
Best Regards

OK Dear Franco, I try to make the last project of the 8 MHz and proves in my test area where I buried three silver coins for two years, eight gold rings buried 6 months and 15 copper coins buried two years and I have several prototypes but I can not detect anything with any lrl of which I have.

about what i tell you about Alonso, just telling to you that your pcb resemble to drawn of Alonso's PCB, But i not told you that your project was Alonso, Sorry for not making me understand.

I send a greeting and a hug and wish the health problem of your wife get better soon.

Lrlman

[LRLMAN]

OK Dear Franco, I try to make the last project of the 8 MHz and proves in my test area where I buried three silver coins for two years, eight gold rings buried 6 months and 15 copper coins buried two years and I have several prototypes but I can not detect anything with any lrl of which I have.

about what i tell you about Alonso, just telling to you that your pcb resemble to drawn of Alonso's PCB, But i not told you that your project was Alonso, Sorry for not making me understand.

I send a greeting and a hug and wish the health problem of your wife get better soon.

Lrlman

And now finally I want to ask you......... how it should be the pcb face down for this lrl? It has copper tracks? or is all full of copper? They must be joined to ground?

greetings.

Lrlman.

[enjoykin4]

Dear FrancoItaly :)

I have sent this message to you here only because i coudn't send private mail because:

Quote:

"enjoykin4, you do not have permission to access this page. This could be due to one of several reasons:

1. Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
2. If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation."

so i am writing here.
............................

I am sorry about your wife is not in good healt. I think i can help you - even if your wife is in last stage of illness.

Currently in Russia exist one very special healing device - special healing technology which name is СВЕТЛ - in translation it means LIGHT, which already has helped many people to get their good health back. It is very special device and vey special cosmic technology of Russian academician - nuclear physicist Nikolai Viktorovitch Levashov (1961-2012).

His official site
http://lлевашов.рф
http://levashov.ws

Don't trust any lies from any internet source about him (soon one day , you will know why) , and his wife Svetlana (1964-2010) and his/her healing technology. My only advice - try it- try this device SVETL and see healing influence at your wifes life. This device is 30 century technology and i am not a lier about it. I am an physicist not seller or shop assistant. I just want to help you and your wife informing you about.

http://svetl.org/sites/default/files/images/%D0%BA%D0%B0%D1%80%D1%82%D0%B8%D0%BD%D0%B02.jpg
Russian academician Nikolai Viktorovitch Levashov

http://levashov.ws/Svetlana/Sveta.jpg
Duchess Svetlana Levashova De Roghan Obolenskaya

One short journey to Sank Peterburg will forever change both of yours life at good.
I advice personal reception and contact with RNTO team - Russian Science Technical Society.

For more information contact mail at Russia.

http://rnto.club/images/logo_RNTO.png
телефон: +7-916-612-19-83
электронная почта: support@svetl.org
Aдpeс: rnto@mail.ru
http://rnto.club/
http://rnto.club/kontakti.html

ps: Quote D'Arsonval: «Anything is possible. But one must not accept anything , except that which can be experimentally
proved. The ideas of an insane person differs from the conceptions of a genious , mainly because experiment invalidates the former and confirms the latter.»

Volhv Enjoykin4 «In quantum physics - there is no difference between Magic and anisotropic realities. Life is Magic and Magic is Life. There is only real light AR RA and real darkness MAR RA».

Good luck
Reg. Enjoykin4 :)

[WM6]

Hi enjoykin4

One thing is, if we are talking about empty hope in case of LRL's and another, if it is about human been health.

I don't like your easy ethic approach with your unapproved promises when you saying:
"I think i can help you - even if your wife is in last stage of illness."

At least your "all-healing" device named Light, didn't work in cases of device inventor and his wife, both passed away. What more proof you need that your "Light" is one healing scam more in an endless series of para-medical fraud?

And you are asking for proof citing D'Arsonval: "... one must not accept anything , except that which can be experimentally proved."

It is clearly experimentally proved, that, if device didn't work in case of device inventor and his wife, then there is no hope that those empty hope device will work for others people in hope too.

Empty hope devices works only to empty pockets of hoping people, nothing else. All other is question of problematic ethic or even a crime.

[FrancoItaly]

Hi LRLMAN,
the pcb face down is full copper and it must be joined to ground.
Best Regards

[FrancoItaly]

Hi enjoykin4,
My LRL isn't lasers (PD), not any laser and not infrared led or sensor. as I said basically it is an Rf amplifier (8Mhz if you use 8Mhz quartz) that's "modulated" by the "phenomenon" as we call the principle that makes possible the detection at a distance of meters or tens of meters. Input tank is in the range of FM (about 100-150Mhz). At the moment all the material is on the forum (pcb and schematic). I build more than 10 lrl but the pcb are drawn by hand without the help of programs and the drawings are not very clear. I counsel you to achieve first the 8Mhz version that I think it's the better. The self-oscillating version is too critic and it is not recommended. The CD4046 version works well but it is a little more complicated to build. A member of this forum told me privately that he had made a good discovery with this version. You may email to me at "sandokan51@libero.it".
Best Regards

[enjoykin4]

Hi enjoykin4

One thing is, if we are talking about empty hope in case of LRL's and another, if it is about human been health.

I don't like your easy ethic approach with your unapproved promises when you saying:
"I think i can help you - even if your wife is in last stage of illness."

At least your "all-healing" device named Light, didn't work in cases of device inventor and his wife, both passed away. What more proof you need that your "Light" is one healing scam more in an endless series of para-medical fraud?

And you are asking for proof citing D'Arsonval: "... one must not accept anything , except that which can be experimentally proved."

It is clearly experimentally proved, that, if device didn't work in case of device inventor and his wife, then there is no hope that those empty hope device will work for others people in hope too.

Empty hope devices works only to empty pockets of hoping people, nothing else. All other is question of problematic ethic or even a crime.


OK WM6 - TO BE HONEST

I DO NOT LIKE YOU AND DO NOT LIKE YOURS SLOVENIAN WORLD-OUTLOOK AT ALL !!!!

You said "THE CRIME" !!

What do you know about "THE CRIME" ?? NOTHING !!

What do you know about Nikolai and Svetlana Levashov ?? NOTHING YOU KNOW !!

How many his and her books you have readed ?? NO ONE BOOK !!

You never heard only one sentence from the lips of Nikolai and Svetlana. Am I right !! Yes of course - because i am telling THE TRUTH !!

What are you know about extraordinary experiments by Svetlana and Nikolai - not only in Russia but also in France and States ?? NOTHING YOU KNOW ABOUT !!

What kind of man you are ??

SOME KIND OF GURU DEVA which has already all answers even before was asked about ??

Or maybe you have been born with all UNIVERSE wisdom and completeness of knowledge requirement ??


FOR YOUR INFORMATION - NIKOLAI AND SVETLANA WERE KILLED BY SECRET JEWISH WORLD GOVERNEMENT (JEWISH ILLUMINATI CABAL). SVETLANA IN FRANCE 2010 IN THEIR CASTLE AND NIKOLAI IN MOSCOW 2012. GOT IT !!

MORE INFO FOR YOU SMARTY !!

BOTH WERE KILLED WITH PSY WEAPON KNOWN AS "MUSIC IN STONE". THAT WEAPON HAVE ONLY WORLD GOVERNEMENT SPECIAL SERVICE - WHICH IS INDEPENDENT FROM ALL INTELLIGENT AND SPECIAL SERVICES IN THE WORLD. THAT WEAPON CAN BLAST YOUR HEART IN PART OF MILLISECOND. DO YOU KNOW WHAT ANY FORENSIC MEDICINE WILL FIND IN THAT CASE ?? NOTHING !! GOT IT !! AND THAT WEAPON IS REAL AND USED IN MANY CIRCUMSTANCES BY SECRET JEWISH BANKERS WORLD GOVERNEMENT !!

YOU COUNTRY SLOVENIA IS UNDER THEIR RULES !! GOT IT SMARTY !!

NEXT TIME READ MUCH MORE AND INFORM YOURSELF BEFORE YOU MAKE FURTHER ANY EMPTY PRESUMPTIONS AND FALSE CONCLUSIONS.

HAVE A LONG NIGHT SMARTY !! GOT IT !!

[enjoykin4]

ok folks - now back to lrl/s. :)

Thank you Mr. FrancoItaly !!

I am plan to replicate all your builds first because the SCALR PHENOMENON and second about THE GOLD. I like both !! :)

Yes - I know it is unusiual Rf amplifier , with unusual mixer stage. Because that I also know that oscillator, input stage and mixer are critical for catching PHENOMENON. Especially are critical position and property of coil L1 in respect to outer Antenna. Also part of RF power you are leading to the outer antena and aground via capacitive coupling. Your grounding is in one point and all return currents go in that point and out via outer aluminium case.

How do you sure you Rf amplifier does not emitting nothing out of body case ?? What if does ?? What if emit - but not standard vector EH-field (rot A) but Scalar field (- div A)? You can't catch any Scalar transmission wia standarn EH receivers. You need a quite a new concept.

Any idea how to do it Mr.FracoItaly ??

I think will be very usefull for detail analyse - your recored of complete LRL RF spectrum as wide as your spectrum analyser can !!

I wish you best luck you and your wife

Will be in touch.

Reg.
Enjoykin

[FrancoItaly]

Hi Enjoykin,
I know very little about scalar waves and I think that it's very difficult to work about. Your analysis on the operation of my LRL is correct and no doubt the influence of the human body is remarkable and it is for this reason that I recommend using a handle very long (25-30cm) to keep the LRL far enough away from the body. As for the shield does not consider it indispensable as I built several units without shielding and work well. As for the origin of the "phenomenon" much it has been said in this forum. I think acting on a wide range of frequencies, for my LRL is the FM frequency and so I think that for proper operation as LRL must be radio emission in this frequency range. Changing the range will need to change the stage mixer.
Best Regards

[enjoykin4]

Ciao stimatissimo signore Franco !! :)

Thank you for informations.
Tell me honestly how did you caught PHENOMENON effect - it is almost impossible thing ??
10 times caught the same PHENOMENON is your greatest success !
It means Italian Golden Eldorado gates were opened for you and your command. !

http://img1.liveinternet.ru/images/attach/c/1//59/759/59759191_x_f7db5e45.jpg

ps: Signore Franco i am thinking about differential configuration of your Scalar receiver. Also PLL version is special interesting for me - because i can meassure very precise phase shift of incoming signal. Only thing i need is Reference Phase - and that reference should not be PLL oscillator. I need something very stable - with a very low jitter (phase noise). For example independent rubidium oscillator placed in field like phase marker. Do you have any idea how PHENOMENON influent crystal lattice or semiconductor structure. Maybe the whole "trick" is not in mixing frequencies but in some sort of semiconductors lattice deformation ? I wish i have answers on these questions.!

Good Luck and best rergards.

Sincerely Enjoykin4

[FrancoItaly]

Hi Enjoykin,
Unfortunately since I built my LRL I had few opportunities to prove it and it is also for this reason that I explained on the forum how to build one, so that others could try it. I do not know if you know that the phenomenon is generated after a few months that the metal is buried and to check the proper functioning is necessary to have a field where do the tests. Or alternatively know a place where it is supposed that there are metals buried, but to do this you should be sure of the proper functioning of the LRL. The only test that I can recommend is to touch the antenna with your hand and check that the signal at the output decreases, it is an empirical proof but it always worked. I think you have read about the compass effect and sky effect that appear when there is too much amplification or if a srl is poorly designed. In practice there is a signal in a particular direction whose intensity does not change as you move in that direction, or is a signal by tilting up or down the LRL.As for the treasures in Italy there is a very strict legislation where practically everything you can find belongs to the state, you can just keep that has no historical or archaeological interest but you still have to share with the owner of the land. but I have already a certain age and I'm glad to share my experience with other forum members around the world and I like to think of these people as "unknown friends." In Italy it says "who finds a friend finds a treasure", but it also says "who finds a treasure find a lot of friends."
Best Regards

[Geo]

Hi LRLMAN,
unfortunately I do not know when I return to Italy as part of my life is spent here in Switzerland with my wife who is not in good health.
.
Best Regards


Hi Franco.
My friend i wish you the best for your wife:)

Regards

[FrancoItaly]

Hi Geo,
Thanks for your good wishes and I hope you and your family are in good health.
Regards

[WM6]

Dear enjoykin4

You aware me.

Sorry to hurt your honorable feelings - it was not intended. Not at all. Sorry.

Will not happen again.

O yes, don't tell me, I have experiences with those mad Illuminati Cabalist personally.
They are trying to kill me at least three times using their weapon "Music in stone". Thankfully they failed.
It could be, that I defended myself by fact that I am total stone in music.

And that is not all. Illuminati stole my almost finished (I need only to give it proper name), LRL project, based on critical third tritium circular non-magnetic resonance harmonic, which are proven as very potent response stimulus for natural gold. This way I was able to detect gold nugget as small as 1gr at 3.14km (even with hill between). Even more, I was even able for extremely remote detecting, par example: I regularly tested this device by detecting 31.415 tons of gold at Illuminati residence in Cannon Street, London. Evidently they have sensed my detection and decide to levied with me. Lucky not, but, sadly, after last Illuminati attack, my fantastic LRL invention has gone along with all plans. I can only imagine what they're now doing with my no-named LRL. I would not be surprised if all gold disappear from earth's crust in short.

So, as you see, no reason for upset.

With best regards from Slovenia, "one of planetary most beautiful destination" (according Russian tourists).
----------------------------------------


PS: Franco, sorry for this small pollution of your valuable thread.
I join all the good wishes to you and your family members.



OK WM6 - TO BE HONEST

I DO NOT LIKE YOU AND DO NOT LIKE YOURS SLOVENIAN WORLD-OUTLOOK AT ALL !!!!

You said "THE CRIME" !!

What do you know about "THE CRIME" ?? NOTHING !!

What do you know about Nikolai and Svetlana Levashov ?? NOTHING YOU KNOW !!

How many his and her books you have readed ?? NO ONE BOOK !!

You never heard only one sentence from the lips of Nikolai and Svetlana. Am I right !! Yes of course - because i am telling THE TRUTH !!

What are you know about extraordinary experiments by Svetlana and Nikolai - not only in Russia but also in France and States ?? NOTHING YOU KNOW ABOUT !!

What kind of man you are ??

SOME KIND OF GURU DEVA which has already all answers even before was asked about ??

Or maybe you have been born with all UNIVERSE wisdom and completeness of knowledge requirement ??


FOR YOUR INFORMATION - NIKOLAI AND SVETLANA WERE KILLED BY SECRET JEWISH WORLD GOVERNEMENT (JEWISH ILLUMINATI CABAL). SVETLANA IN FRANCE 2010 IN THEIR CASTLE AND NIKOLAI IN MOSCOW 2012. GOT IT !!

MORE INFO FOR YOU SMARTY !!

BOTH WERE KILLED WITH PSY WEAPON KNOWN AS "MUSIC IN STONE". THAT WEAPON HAVE ONLY WORLD GOVERNEMENT SPECIAL SERVICE - WHICH IS INDEPENDENT FROM ALL INTELLIGENT AND SPECIAL SERVICES IN THE WORLD. THAT WEAPON CAN BLAST YOUR HEART IN PART OF MILLISECOND. DO YOU KNOW WHAT ANY FORENSIC MEDICINE WILL FIND IN THAT CASE ?? NOTHING !! GOT IT !! AND THAT WEAPON IS REAL AND USED IN MANY CIRCUMSTANCES BY SECRET JEWISH BANKERS WORLD GOVERNEMENT !!

YOU COUNTRY SLOVENIA IS UNDER THEIR RULES !! GOT IT SMARTY !!

NEXT TIME READ MUCH MORE AND INFORM YOURSELF BEFORE YOU MAKE FURTHER ANY EMPTY PRESUMPTIONS AND FALSE CONCLUSIONS.

HAVE A LONG NIGHT SMARTY !! GOT IT !!

[FrancoItaly]

Hi WM6,
thanks for your good wishes, although in the world of LRL we are diametrically opposed points I appreciate your expertise. I'm curious to know if you have ever made some kind of LRL?
Regards

[humhum]

Hi dear WM6 , What is '' based on critical third tritium circular non-magnetic resonance harmonic''

[nelson]

Hi Franco

I´m sorry to heard that your wife is in bad health condition. I just want to wish you and your wife, the best, and thrust in good that everything will go fine.


Hi Geo,
Thanks for your good wishes and I hope you and your family are in good health.
Regards

[LRLMAN]

Hi LRLMAN,
the pcb face down is full copper and it must be joined to ground.
Best Regards

Hello Franco, thank you very much for the information, I will try to do this project and I'll be posting the return results of its operation in my field test and outdoor.

Thanks in advance.

Lrlman.

[FrancoItaly]

Hi Nelson,
thanks for your good wishes.
Best Regards

[enjoykin4]

Dear signore Franco

Would you share with us all your original 10 PCBs design for your LRL Scalar receivers ?? PLL version, Quartz version and all others.

Also i want to know characteristics of PCB epoxy - dielectric constant, thickness, dimensions. I want to replicate only your original designs and research all about Scalar Phenomenon. As i said before orientation of components, coils, antennas with pcb tracks together with epoxy boards properies are crucial for catching Scalar Phenomenon of old Gold treasuries. Looking from that perspective to Gold Transmutation (of old dust) maybe is a small step. Who knows ?? We need a new concept - «If you can't find old treasury Gold - make it from mercury, old iron - or maybe transuranian elements». :D

The proof about non original pcb's - no one pcb design here except Signore Franco have gave Phenomenon Effect. So these pcb designs are useless. Also , almost all pcb's were made at two sides which is wrong. Signore Franco designs are simple single side PCB's with another side as massive ground plane.

The Goal is CATCJING PHENOMENON and after than you can design even 16 layers pcb's when you KNOW HOW CATCH PHENOMENON !!

Best Regards
Enjoykin

[enjoykin4]

Dear signore Franco

Scalar Radio is reallity today in 21st century.

Check the home of Scalar transmissions - xferra.Ru

http://www.xferra.ru - on Russian
http://www.xferra.com - on English

http://www.xferra.com/upload/medialibrary/32c/32c1f80cd8baef8bb15f8dec86b748f5.png

XFERRA is the first Scalar underground Transceiver radio station which can be obtain from Russia on request at this link:
«HF communication», xferra@mail.ru, +7 3812 292464
Kharkovskaya str. 23 office 123, Omsk, 644041, Russia

Russian ministry of extreme situations МЧС use these transceivers for their urgent mobile teams.

Signore Franco you like most experienced electronic engineer here with 65 year practice in electronic skills and art , perfectly well know that classical vector EH transmission from mine working through 1 km rock strata is impossible thing. Simple because vector field can not penetrate through such big layer of rocks and mine metal constructions.

For Scalar magnetic field such restrictions does not worth. Longitudinal Scalar waves with easy penetrate through any dielectric even through entite planetary core. Secret of Long Range Gold detections was based on these Longitudinal waves. Scalar waves as you know is ideal thing for new weapons on newest physical principles, overunity generators and many many more unknown things. Why Scalar physics had been banned by main stream science from the time of Cabbal man A.Einstain (one of bankers pawns) is long and different story.

Signore Franco i want to pick your attention at Xferra Scalar antenna which is very very similar yours LRL 70 windings antenna.

So i am wainting your new contributions and continuation of these very interesting and useful topic.

Best wishes
Enjoykin4

[FrancoItaly]

Hi Enjoykin4,
As I said now I am away from my home in Italy and do not know when I can come back enough time to the LRL. However it would be difficult to photograph all the pcb without dismantling the LRL. I can say that the arrangement of components on the PCB and the type of pbc, single or double-sided, are not influential for the detection of the phenomenon, rather advise you not to make them too miniaturized to avoid auto-oscillations.For the moment I do not want to venture into a field still too unknown as longitudinal waves also because my LRL works well.
Best Regards

[enjoykin4]

Ok Mr.Franco - I understand.

I have had good intention to share my knowledge and experience about Scalar physics - but as nobody interested it makes no sense posting additional informations.

So folks good luck to all - you need it for finding a lot of gold.

Best wishes to all
Enjoykin4 - няш-мяш !! :)

[FrancoItaly]

Hi Enjoykin4,
It's not that I do not have interest to scalar waves but do not have the necessary time. If you think that they apply in the LRL you can experiment with scalar waves and metals buried, but I would not know where to start. You could you build such a generator of scalar waves and also a receiver?
Best Regards

[WM6]

Hi dear WM6 , What is '' based on critical third tritium circular non-magnetic resonance harmonic''

Dear humhum, I abandoned this "tritium" project after all data lost.

There are more interesting shortcuts to gold uncovering, than remote sensing electronic devices. We only need to improve our hidden and yet vestigial time travel abilities. Once we become skilled in time travel, it is easy to observe back in time, who and where is buried gold treasure. And then we only need to dig it:

http://totalizm2007.pasozyci.cba.pl/timevehicle.htm


Hi Enjoykin4,
You could you build such a generator of scalar waves and also a receiver?
Best Regards

Hope enjoykin will give us such one device.

Problem with so called scalar waves is, that we can use it for communication through solid substance, but not for make GPR like echoes of underground artifacts. Scalar waves are almost inert to to changes in the density of the solid underground substance through which penetrate. Not suitable for GPR like device (OK they can detect submarine buried at 100m distance, but there are a lot /even simple/ means to do that). If it were not so, scalar waves would not be so useful for underground communications.

[darkman]

Mr franco:
tr1 emitter = 4.83 v
tr2 collector = 5.59 v (with full led on when i check it)
tr3 collector = 5.22 v (with full led on when i check it)
tr4 collector = 5.84 v .
tr5 emitter = 0.30 v (for 1 sec ) then = 0 v .
all volts is dc-volt
note : C15: in= 5.84 , out= 0 to 0.12 v .
i try every thing to make the output more than 0 v .
what do you think ?
regards

[FrancoItaly]

Hi darkman,
The DC voltage of TR1, TR2, TR3 and TR4 are appropriate, you have to check if the stage of TR1 oscillates, for that you need an oscilloscope at TR1 emitter. If you do not have a scope you can disconnect a terminal of C15 from TR4 collector to TR1 emitter and check if the TR5 emitter is in 1 - 5V DC range. If the TR1 stage does not oscillate you have to increase the value of C1 to 390 pF or 470 pF or 560pF. If the stage of TR1 oscillates in place of C2, C3 and C4 using a 1pF capacitor or 2pF. IF the DC output is still 0V you have to increase C13 and/or C14 using 560-680-820pf or more. I hope to be as helpful.

[putrechigi]

you are greet!!!!

Dear FrancoItaly :)

I have sent this message to you here only because i coudn't send private mail because:

Quote:

"enjoykin4, you do not have permission to access this page. This could be due to one of several reasons:

1. Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
2. If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation."

so i am writing here.
............................

I am sorry about your wife is not in good healt. I think i can help you - even if your wife is in last stage of illness.

Currently in Russia exist one very special healing device - special healing technology which name is СВЕТЛ - in translation it means LIGHT, which already has helped many people to get their good health back. It is very special device and vey special cosmic technology of Russian academician - nuclear physicist Nikolai Viktorovitch Levashov (1961-2012).

His official site
http://lлевашов.рф
http://levashov.ws

Don't trust any lies from any internet source about him (soon one day , you will know why) , and his wife Svetlana (1964-2010) and his/her healing technology. My only advice - try it- try this device SVETL and see healing influence at your wifes life. This device is 30 century technology and i am not a lier about it. I am an physicist not seller or shop assistant. I just want to help you and your wife informing you about.

http://svetl.org/sites/default/files/images/%D0%BA%D0%B0%D1%80%D1%82%D0%B8%D0%BD%D0%B02.jpg
Russian academician Nikolai Viktorovitch Levashov

http://levashov.ws/Svetlana/Sveta.jpg
Duchess Svetlana Levashova De Roghan Obolenskaya

One short journey to Sank Peterburg will forever change both of yours life at good.
I advice personal reception and contact with RNTO team - Russian Science Technical Society.

For more information contact mail at Russia.

http://rnto.club/images/logo_RNTO.png
телефон: +7-916-612-19-83
электронная почта: support@svetl.org
Aдpeс: rnto@mail.ru
http://rnto.club/
http://rnto.club/kontakti.html

ps: Quote D'Arsonval: «Anything is possible. But one must not accept anything , except that which can be experimentally
proved. The ideas of an insane person differs from the conceptions of a genious , mainly because experiment invalidates the former and confirms the latter.»

Volhv Enjoykin4 «In quantum physics - there is no difference between Magic and anisotropic realities. Life is Magic and Magic is Life. There is only real light AR RA and real darkness MAR RA».

Good luck
Reg. Enjoykin4 :)

[edwgold]

Ok Mr.Franco - I understand.

I have had good intention to share my knowledge and experience about Scalar physics - but as nobody interested it makes no sense posting additional informations.

So folks good luck to all - you need it for finding a lot of gold.

Best wishes to all
Enjoykin4 - няш-мяш !! :)

Hi Enjoykin4,

You say that gold can be detected through scalar waves. As it would be the method?

[darkman]

Hi darkman,
The DC voltage of TR1, TR2, TR3 and TR4 are appropriate, you have to check if the stage of TR1 oscillates, for that you need an oscilloscope at TR1 emitter. If you do not have a scope you can disconnect a terminal of C15 from TR4 collector to TR1 emitter and check if the TR5 emitter is in 1 - 5V DC range. If the TR1 stage does not oscillate you have to increase the value of C1 to 390 pF or 470 pF or 560pF. If the stage of TR1 oscillates in place of C2, C3 and C4 using a 1pF capacitor or 2pF. IF the DC output is still 0V you have to increase C13 and/or C14 using 560-680-820pf or more. I hope to be as helpful.

thx Mr Franco .
i am using 2pF capacitor on (C2,3,4) , and C13 and C14 = 1nf , and it work's i got 2 vdc on output .
but when i touch the antenna the volt's drop Up ! and all led's on ?!
regards :)

[FrancoItaly]

Hi darkman,
I think that isn't important if voltage drops up or drops down, this is only a way for testing the lrl empirically, in this way we are sure that the gain is correct (not too low and not too high to saturate). Now you have to try it on the test field.
Regards

[darkman]

Hi darkman,
I think that isn't important if voltage drops up or drops down, this is only a way for testing the lrl empirically, in this way we are sure that the gain is correct (not too low and not too high to saturate). Now you have to try it on the test field.
Regards

thank you Mr franco :)

i will try it on test field next week and back with The result , i have 2kg of copper 40cm depth .. 4 month long
Regards

[abdou2014]

HELLO FRANCO . YOU TOLD . IF WE WANT KNOW IF YOUR LRL WORK WELL . THE LED MUST BE OFF WHEN WE PUT OUR HAND NEAR THE ANTENNA . SO WHEN WE ARE OUTSIDE NEAR THE TARGET WHAT WILL HAPPEN TO LED. ON TO OFF OR OFF TO ON ???

[FrancoItaly]

With target the led goes on.

[abdou2014]

Hi Mr FRANCO. THANKS FOR REPLY . I FOUND TARGET WITH GG 918 AND WHEN I TRY TO CONFIRM IT WITH YOUR LRL NOT WORK .

[FrancoItaly]

I never tried the GG 918 but it is possible that the sensor stage of my lrl does not have enough gain, if this is the case it is necessary to increase the gain of the next stage; if you've made a version with 1 LED should be reduced R10, from 220K to 68K or 47K. If you have made a version with 3 LEDs must be increased R2 from 220K to 560K and decrease R1 from 150K to 47K. The sensitivity also increases extending the antenna from about 30 cm to 50-60cm or more. It is also possible that the LRL works in reverse way, that is, the signal decreases in the presence of the target. To check this you have to adjust the threshold in order to have the first LED just turned on and verify if the LRL will switch off in the presence of the target.

[abdou2014]

thanks Mr Franco . you told ( It is also possible that the LRL works in reverse way )
so, how reverse it . and make it correct .

[FrancoItaly]

Many wishes for a Happy New Year to all the members of this forum. We all hope to find a treasure, but the biggest treasure is health although a treasure (even small) can help your health!

[enjoykin4]

to all !!

Happy New 7524 year (counting from ancient Grande TarhTaria victory agains Chinese empire 7524 years ago, or C.M.З.Х in Russian ancient calendar (Koladi dar). Grande Tarhtaria had been destoyed before something more of 200 years ago by Thermo-Nuclear bombs of Koscheys (masters of the "Grays"). Koscheys are Cosmic Parasites (dark forces of Universe) or Cosmic Evil race ( not humanod) and complete mankind past (not history @HIS TORAH@) had been rewritten to help Jewsih Illuminati Cabal (Planetary Social Parasites) to conquere and enslave human race and destroy mankind according to wishes and orders of their evil @Cosmic fathers@.

Yes folks this is a TRUTH. Complete mankind past is upside down !! :nono:

http://www.wedjat.ru/images/nytree2016.png

Signore Franco !!
Many good health and long life you and your wife and yours family and also best wishes to all members of LRL-forum.

With respect
Enjoykin4 !!

Всем удачи !! :)

[enjoykin4]

http://tesla.zabotavdome.ru

http://tesla.zabotavdome.ru/images/rt800x600.jpg

Some tips and tricks about Scalar Magnetic Field (only for experimenters) !!

Very simple representation of S and V fields.

a) Scalar Longitudinal wave transmmision.
b) Vector Transversal wave transmission.
http://tesla.zabotavdome.ru/images/slinky_waves.jpg


Scalar Magnetic Field show yourself (can be detectable) only in case of resonance oscillating electronic circuit with bucking coils (partnered) configuration. For example it is famous Nikolai Tesla bifilar configuration which is pure scalar coil configuration.

http://tesla.zabotavdome.ru/images/bifilyar.jpg

Nikolai Tesla bifilar coil. (dont forget to put it in resonance)

Signore Franco configuraton is same bucking configuration because his stylus (or coil) antenna together with parallel oscillating circuit L1C1 can be represented like partnered bucking configuration. Imagine stylus (or coil) antenna like may lumped parallel oscillating circuits, conected serially with own resonant frequency.

http://tesla.zabotavdome.ru/images/2res.jpg

Yellow trace - resonance of bifilar winding 34.298 KHz.
Blue trace - inductor resonanace (excitation coil) 41.6KHz.
Strange Phase Shift at 41.120KHz.

To get proper resonancematching - the rule is simple - Frequency of excitation coil (inductor) should be exactly resonant frequency of bifilar coil. Anomaly - any active resistance connected at bifilar coil does not change amplitude of source signal (generator or inductor coil). It means - any LOAD does not influent SOURCE. There is ZERO (0) coupling LOAD->SOURCE or simple you have got unipolar feedback. It means you dont waste energy from the source - only change phase shift of source signal. Taking in account Scalar Waves and GOLD-SILVER-COPPER.... it means you can passive sniff precious metals (long time in ground) only tracking phase shift change which they make - making proper scalar field range of actions.

more informations and many interesting links about Scalar waves here:

http://tesla.zabotavdome.ru



Томилин А.К. О Свойства векторного электродинамического потенциала (http://www.sciteclibrary.ru/texsts/rus/stat/st2123.htm)
Стефан Маринов (http://tesla.zabotavdome.ru/books/marinov.pdf)
Униполярный генератор Тесла. (http://www.teslatech.com.ua/index.php?option=com_content&view=article&id=47&Itemid=48)
Диалоги о науке. ЭРГЕНТОР (http://torsmagnit.jimdo.com/%D0%B3%D0%B8%D0%BF%D0%BE%D1%82%D0%B5%D0%B7%D0%B0/%D1%87%D0%B0%D1%81%D1%82%D1%8C-i/)
Г. Т. Касьянов "УСКОРИТЕЛЬ ЭЛЕКТРОНОВ"(Проверить) (http://www.rusphysics.ru/articles/244/)
Первеев Г.П. (http://ut27972.narod.ru/Book_2/109_B_2_p_109.htm)
Соединение обмоток трансформаторов (http://www.avellinfo.ru/elektronika/soed_obm_1.html)
Калькулятор. Заряд конденсатора от источника постоянной ЭДС (http://planetcalc.ru/1978/)
Евгений Михайлович Ефимов. Реализация односторонней индуктивной связи. (http://tesla.zabotavdome.ru/books/ms.doc)
Резонансный усилитель мощности. (http://www.freepatent.ru/patents/2517378)
Евгений Михайлович Ефимов. Реализация односторонней индуктивной связи. (http://ale.io.ua/s205870/sposob_realizacii_odnostoronney_induktivnoy_svyazi )
Инвертор реактивной мощности (http://misating.do.am/news/energy_saver/2014-04-05-162)
А.В.Чернетский Плазменно-вакуумный эффект. (http://tesla.zabotavdome.ru/books/chernetsky.doc)
Патент Клёсова В.А. (https://cloud.mail.ru/public/e755769a0967/%D0%9A%D0%BB%D1%91%D1%81%D0%BE%D0%B2)
ОЭДС (Проверить) (http://realstrannik.com/forum/razdel-avtorskikh-tem/289-po-doroge-k-btg.html)
Heating device that produces 17 times more heat than the "equivalent" (Проверить) (http://www.energeticforum.com/inductive-resistor/4314-cop-17-heater-rosemary-ainslie.html)
Pre zero crossing detection (http://tesla.zabotavdome.ru/books/pre-zero_crossing.pdf)
Генераторы гармонических сигналов с LTSpice моделям (http://zpostbox.ru/sine_wave_oscillators.html)



PS: GO FOR IT - SIGNORE FRANCO SCALAR SNIFFER !! IT WORTH !! CHECKED AND TESTED BY ENJOYKIN4 !!

With respect
enjoykin4 - няш мяш !! :)

[FrancoItaly]

Hi enjoykin4,
Very interesting but in my lrl (quartz version) there is only a 8Mhz oscillator (not tunable) and a tank circuit L1C1 (in the range 100Mhz-150Mhz). With CD4046 version we can measure the phase shift with no target and with target. With a more elaborate version of this lrl we can measure simultaneously the variations in amplitude and phase.I created this to get a kind of discrimination between gold and other metals but with poor results. Scalar waves could still explain the operation of the LRL. I'm glad you've tested positive my LRL, can you tell me some details?
Best regards

[Geo]

Hi Franco.
I have construct the xtal version (again) so to put it inside an new LRL that i have build this month but has some problems.
1. when i touch the antenna led don't turns on, but if it is on then it turns off.
2. with full sensitivity don't works as compass....
3. don't detects a gold buried coin but other lrl detects it.
Signal at collector of TR2 is 10mv p-p, at TR3 =110mv and at TR4 is 1.05V.


Any idea???

Regards:)

[FrancoItaly]

Hi Geo,
1. It may be that it works in reverse way, try change input+ and input- at the first operational (LM358)
2. As I said in other thread If there isn't compass effect with max gain it is necessary to increase the gain of the LM358. With the gain at most there must be the compass effect, so you have to decrease until it disappears.
3. The use of the oscilloscope may change the behavior of the amplifier stages, it is best to measure the DC voltage of the emitter of TR5 which must be in the range 1-6V, also the DC voltages of the collectors of all the transistors (TR2-TR3-TR4) must be in the range 3-5V.

Regards

[abdou2014]

i built all version of your lrl , and lot of prototype of 8 mhz stage with modification , we can realise two receiver . magnetic and static

[FrancoItaly]

do you mean magnetic receiver for my lrl?

[abdou2014]

yes !

[FrancoItaly]

A magnetic receiver requires a magnetic antenna which can be a coil wound in the air or a ferrite antenna. In my lrl there is only an electric antenna, can you explain better?

[abdou2014]

of course i tried it with different antennas , and it can detect small transmiter from 3 meters

[FrancoItaly]

But it works as LRL?

[abdou2014]

I think. but i have not yet detected gold with it , what is the final step for you , can you help me ?

[Geo]

of course i tried it with different antennas , and it can detect small transmiter from 3 meters

So it is a radio... but are not all radios lrls.
Maybe a radio to catch a signal from a buried object but generally most radios don't have this ability. Make a test field with a buried object and try to locate it after some months. All the other are only to doing chat.....

[abdou2014]

Thanks Mr Geo .

[enjoykin4]

Signore Franco

Actually, according to professor Dr.Gennadiy Vasilevich Nikolaev - magnetic fields does not exist in nature (nor Vector - nor Scalar magnetic fields).

There are exist only GRADIENT ELECTRIC FIELDS which were caused by DELAYED POTENTIALS and deformation of COULOMB FILED at the movement of charges.

MODERN ELECTRODYNAMICS by Dr.Gennady V. Nikolaev
http://doverchiv.narod.ru/Nikolaev/Nikolaev_modern_electrodynamics.htm

Reg. from Russia
Enjoykin4 :)

[enjoykin4]

Signore Franco

what is maximum detection distance and maximum detection depth of yours PLL4046 LRL ??
20 - 30 meters or more ?? about depth can detect big golden deposite 3-5 meters in soil ??

does your PLL4046 LRL detect "PHENOMENN" induced only by gold and silver or all other noble and non-noble metals in the soil ??

Best regards
Enjoykin4

[FrancoItaly]

Hi enjoykin4,
I tested the 4046 lrl in the same test field of quartz lrl and I found that they had the same performance and I did not other tests in a real field. AS I said to Geo to achieve better performance with maximun gain you must have the compass effect, if it's not the case you have to increase the gain of LM358.
Best Regards

[FrancoItaly]

Hi enjoykin4,
I think that the lrl reveals all no ferrous metals but the maximum sensibility is for gold and silver. I found a brass cartridge at 1 meter distance and 2 cm buried.
Best Regards

[enjoykin4]

Thank you Signore Franco !! :)

Best Regards from Russia
Enjoykin4

[Arionas]

Τhanxs Mr.Franco

[enjoykin4]

Signore Franco do you ready to open gold hunting season in Italy this 2016 (7524) year ??

I hope your wife's health will be OK and you will find time for Gold prospecting !! :)

Signore Franco in the present Russian article, are some ideas how to boost location distance and prospecting depth of your Quartz LRL (called on this forum Franco Phantom LRL) and also PLL4046 LRL using 2-Spiral coils (2S-Coils) antenna as a low impendance input part of your "Scalar detector". Keep in mind that 2S-Coils are sclara type coils (both working in opposite phase to each other) and how has demonstrated by researchers 2S-Coils field is localized in the near-field zone and the that filed has more uniform structure than the field of the conventional spiral coils(like is case of your 70 turns coil). Also 2S-Coils has higher sensitivity to sclara signals (read sensitivity to Gold and Silver) than the analogous conventional coils.

A two-spiral flat coil for detecting 14N NQR signals
ARTICLE from RUSSIAN PHYSICS JOURNAL · SEPTEMBER 2005

Download free at
https://www.researchgate.net/profile/G_Mozzhukhin/publication/243168858_A_two-spiral_flat_coil_for_detecting_14N_NQR_signals/links/00b495284d175b9268000000.pdf?origin=publication_li st

Best regards
Enjoykin4

[WM6]

Hi enjoykin, thanks for link, but there is no data in publication, if coil should be driven by sine or square wave.

Or it is no matter of wave shape?

[FrancoItaly]

Hi enjoykin4,
Unfortunately at the moment I do not know when I'll start the season for the gold, but I hope that many friends in the forum have luck. Thanks for the link to the article related to two flat spiral coil, but I'm just a hobbyist and not an engineer or a physicist, but I deal with electronic more than 50 years (I was 14). The particularity of my antenna coil is that the two ends are connected together and it would be interesting to study its features.
Best Regards

[enjoykin4]

Hi WM6

I think that no matter of wave shape !! :)

Best regards
enjoykin4

[enjoykin4]

Hi FrancoItaly

Yes of course. Also in my oppinion will be very interesting study Scalar Caduceus coil in your LRL :)

http://jnaudin.free.fr/images/caduceus.gifhttp://jnaudin.free.fr/images/swtcoil.jpg

The coil is wound on a 45 degree angle up and down the length of the form creating a series of 90 degree intersections along the full lenght.

http://www.treurniet.ca/Smith/SmithCoil.htm

Best regards
enjoykin4

[KwstasXri]

Hi FrancoItaly

Yes of course. Also in my oppinion will be very interesting study Scalar Caduceus coil in your LRL :)

http://jnaudin.free.fr/images/caduceus.gifhttp://jnaudin.free.fr/images/swtcoil.jpg

The coil is wound on a 45 degree angle up and down the length of the form creating a series of 90 degree intersections along the full lenght.

http://www.treurniet.ca/Smith/SmithCoil.htm

Best regards
enjoykin4
Hi Mr FrancoItaly,
It's the first time i've been in this forum and i want to thank you in advance for the drawings and the right information you provide us.
Today i've managed to make the PCB from 8MHz sensor.
After i've done the tests you've written in this forum..especially the one where i had to put my hands near the antenna...it worked and the led turned on...i would like to know if all of the three leds need to turn on..or just one of them? how could i know that there's a coordination in P1 and P2? also..the out of sensor stage is 5,26 V.
thank you very much for your help!

[KwstasXri]

Hi enjoykin4,
Unfortunately at the moment I do not know when I'll start the season for the gold, but I hope that many friends in the forum have luck. Thanks for the link to the article related to two flat spiral coil, but I'm just a hobbyist and not an engineer or a physicist, but I deal with electronic more than 50 years (I was 14). The particularity of my antenna coil is that the two ends are connected together and it would be interesting to study its features.
Best Regards
Hi Mr FrancoItaly,
It's the first time i've been in this forum and i want to thank you in advance for the drawings and the right information you provide us.
Today i've managed to make the PCB from 8MHz sensor.
After i've done the tests you've written in this forum..especially the one where i had to put my hands near the antenna...it worked and the led turned on...i would like to know if all of the three leds need to turn on..or just one of them? how could i know that there's a coordination in P1 and P2? also..the out of sensor stage is 5,26 V.
thank you very much for your help!

[KwstasXri]

Hi enjoykin4,
Unfortunately at the moment I do not know when I'll start the season for the gold, but I hope that many friends in the forum have luck. Thanks for the link to the article related to two flat spiral coil, but I'm just a hobbyist and not an engineer or a physicist, but I deal with electronic more than 50 years (I was 14). The particularity of my antenna coil is that the two ends are connected together and it would be interesting to study its features.
Best Regards
Hi Mr FrancoItaly,
It's the first time i've been in this forum and i want to thank you in advance for the drawings and the right information you provide us.
Today i've managed to make the PCB from 8MHz sensor.
After i've done the tests you've written in this forum..especially the one where i had to put my hands near the antenna...it worked and the led turned on...i would like to know if all of the three leds need to turn on..or just one of them? how could i know that there's a coordination in P1 and P2? also..the out of sensor stage is 5,26 V.
thank you very much for your help!

[FrancoItaly]

Hi KwstasXri,
P1 is used to adjust the threshold and P2 adjusts the gain, they are not independent, varying P2, P1 needs to be adjusted again. P2 can be adjusted once and for all. It is sufficient that turns on only one led but normally the LED turns off by touching the antenna. Usually touching the antenna at the output of sensor stage the signal goes low and with a good target
the signal augments, but I think that it's important that there is a signal change, negative or positive. It's also useful to shield the box where is the pcb.
Best Regards

[KwstasXri]

Hi KwstasXri,
P1 is used to adjust the threshold and P2 adjusts the gain, they are not independent, varying P2, P1 needs to be adjusted again. P2 can be adjusted once and for all. It is sufficient that turns on only one led but normally the LED turns off by touching the antenna. Usually touching the antenna at the output of sensor stage the signal goes low and with a good target
the signal augments, but I think that it's important that there is a signal change, negative or positive. It's also useful to shield the box where is the pcb.
Best Regards
Mr FrancoItaly...thank very much!

[taxma1981]

I think the lrl with 4046 work fine franko

https://youtu.be/1WOUHEp-EBE

[FrancoItaly]

Hi taxma1981,
this test demonstrates that LRL works well in a closed environment, almost certainly it works outdoors. Naturally LRL is also sensitive to the electromagnetic signal sources that fall in the frequency range of the LRL.
Best Regards

[taxma1981]

Hi franko and thanks for the bmw lrl haha,it is work very fine
https://youtu.be/E6GMjF44hNM

[indiana jones]

Hi franko and thanks for the bmw lrl haha,it is work very fine
https://youtu.be/E6GMjF44hNM

Nice work Aki.

BMW
Bayerischer Mist Werke

[taxma1981]

Nice work Aki.

BMW
Bayerischer Mist Werke

:χαχαχα::χαχαχα: indiana das ist deine plakette

[enjoykin4]

Hello Taxma1981

Can you share with all here - oscillographs from your working PLL4046 LRL from the most important points like GEO did and also pictures of your PCB ?? :)

Best Regards
Enjoykin4

[taxma1981]

The board is from Indiana, only indiana has a pcb

[taxma1981]

One more test,this lrl work perfekt
https://youtu.be/4nGxc7xCLOg

[enjoykin4]

taxma1981 PROVE your PLL4046 LRL is working ??

Go to the test field and dig up some golden coins ?? :lol:

Regards
Enjoykin4

[enjoykin4]

OK folks let's open the cards !! :lol:

http://www.partyhunterz.com/components/com_virtuemart/shop_image/product/Playing_Cards_4f7c0313d5223.gif


Dear signore FrancoItaly Phantom LRL and PLL4046 LRL are working but ...... one no !!

It is extremely difficult - near critic to adjust properly work and tune it to catch gold and silver frequencies !!

In my oppinion problem is in extremely sharp slope of capacitance to voltage convertor - couple of hundred femtofarads for full scale output voltage 6V DC..

This "Scalar phenomenon" boost the output voltage - it means we need to tune positive feedback between "Golden signal" and signore Franco LRL's,

How to boost maximum sensitivity ??

When we touch tha antenna with bare hand(s) voltage must drop immediately to 0V (zero volts). It means that capacitive coupling between primary oscillating circuit - antenna with coil L1 and capacitor 22 pf in parallel to coil with internal oscillaor (8MHz or 3MHzPLL) must be couple of hundred femtofarads. Also peak to peak sinusoidal voltage of internal oscillator must not be to high - not higher than 1Vpp (1Volt peak positive to 1Volt peak negative sinus).

Scalar phenomenon (read Golden signal) increase capacitive coupling between antenna-L1C1 and several serial capacitors 1pf connectd to internal LRL oscillator (8MHz or 3MHzPLL) up to tenth picofarads which make shunt (in parallel) over several serial 1pf capacitors so the great ammount of RMS RF power comes to base of second transistor T2 and after additional amplification, rectification and filtering we got a pure 6V DC voltage at output. The key for detecting phenomenon is influence of Scalar signal to several capacitors. On some way their capacitance rise to ten or maybe hundred times higher value than inicial but only while Scalar signal make longitudinal transient through.

I dont think transistor T2 is key to reveal scalar phenomenon but spatial relationship between antenna-primary coil L1C1-several coupling capacitors and internal oscillator. It is like Scalar signal make tunneling of main oscillator signal and in same time boost him to high amplitude.

I think it is a crucial thing makeing PCB exactly like signore Franco did and start fighting with "phantom" capacitive feedback.

Also check your LRL - it must be insensitive to ground (not rise and not drop output voltage).

Best Regards from Russia :)
Enjoykin4

[FrancoItaly]

Hi enjoykin4,
Only one of my 10 lrls worked bad (quartz lrl) and I don't understand the cause, the pcb was the same and also the components. Probably parasitic couplings were the cause, we must not forget that the my first lrl was a rf sniffer that went to autoscillate. We must also remember that there is a base/emitter capacitance (TR2 and all BC... transistors) of about 10pF that is in parallel with 22pF capacitor, if we take away 22Pf capacitor the lrl works well anyway. You're right "peak to peak sinusoidal voltage of internal oscillator must not be to high - not higher than 1Vpp (1Volt peak positive to 1Volt peak negative sinus)." this is why quartz LRL is easier to develop, indeed the oscillator output is few volts peak to peak.
Best Regards

[enjoykin4]

Thank you signore Franco !! :)

Best regards
enjoykin4

[enjoykin4]

FrancoItaly Hello !! :)

Do you have spare time for additional experiments in your laboratory with your LRLs.
Want to help to try catch "Scalar phenomenon".

Knowing that scalar longitudinal wave running through copper conductor changing polarity at exact same distance (for example at every 40 cm) - already checked with compass running HV scalar phenomenon (induced type) , you can try to build kind of scalar detector in form of Rogowski current sensor using toroidal type windings and make realtime recording using your frontend digital sempling oscillograph (Le Croy type I guess ??) as a real time recorder. It is very useful to make in same time wide band spectra recording in near field using independent spectral analyser and stylus antenna at input.

Something similar did Esteban in 2010 and much earlier in 1970th Professor Gennadiy Vasilevitch Nikolaev in his Tomsk Laboratory.

http://www.longrangelocators.com/forums/attachment.php?attachmentid=11699&stc=1&d=1270044977

You shoud to know that when toroidal core with radial winding excited at proper way doesnt catch transversal (vector type) EM waves - because they all are closed (concentrated) in interior structure of toroid while in same time longitudinal scalar wave (both polarity [plus,minus] has maximum amplitude in axial axis of toroid coil. These all means you need additional pair of windings (perpendicular to radial [vector windings]) to catch scalar longitudinal wave while running through stylus antenna.

It semms to me you are only person and only HUMAN here who want to cooperate and share your great knowledge and experience in contrary to some persons who give nothing but only catch informations for own "slavery glory" and polite and nice words from their bosses in secret services and all other "spy agencies".

Yes my dear frioend Franco it is VERY HARD to be a HUMAN like YOU and very easy to be @slave specialists for LRLs@ like many on this forum.

Rogowski Coil
http://en.academic.ru/dic.nsf/enwiki/148752

Rogowski Coil
https://en.wikipedia.org/wiki/Rogowski_coil

Rogowski Coil Construction
http://electrical-engineering-portal.com/rogowski-coil-construction

Rogowski and Current Measurement
http://www.pemuk.com

Rogowski Coil sensor
http://www.powertekuk.com/cwtmini.htm

key words:
http://www.nigma.ru/?s=rogowski+coil+how+to+make&t=web&rg=t%3D%D0%9A%D1%83%D1%80%D1%81%D0%BA_c%3D%D0%A0%D 0%BE%D1%81%D1%81%D0%B8%D1%8F_&rg_view=%D0%9A%D1%83%D1%80%D1%81%D0%BA%D0%B5&yn=1&gl=1&rm=1&ms=1&yh=1&av=1&nm=1&lang=all&srt=0&sf=1


.................................................. ......................


Be health and in good will !!!! :)
Best regards from me
Enjoykin4

[enjoykin4]

Signore Franco maybe I am wrong ??

Maybe is not a good idea to share my knowledge and experience in Physics but put rose googles at my eyes and look on this shiny, perfectly, nice ROSE WORLD - and this PARASITIC CIVILIZATION (of SATANIC JEWISH TYPE) in all rose colours - like many do ??

http://www.blogcdn.com/www.joystiq.com/media/2008/05/tmpphpjb3pc2-rose-tinted-glasses.jpg
what a shiny happy people ! ........


PS: This is a question i still have not answered yourself..... :nono:

[FrancoItaly]

Hi enjoykin4,
Unfortunately I'm away from my laboratory, I have to watch my wife here and I have no electronic instrument, only a tester. I own a digital and an analog oscilloscope and many electronic components but unfortunately they are in Italy. I think that's always a good idea to share knowledge and experience, it's the only way to progress. I thought a lot before posting my LRL on the forum, but then I felt it was the best and I would have got benefits too. I wanted to confirm the proper functioning and maybe someone might improve it. I have helped many people privately with email and one confirmed to me a very good find, and this made me very happy. This was the only way to keep alive the forum. First it was a long series of disputes between believed in the phenomenon and others who ironically also denied the existence of the phenomenon. I now believe that there are no doubts about the existence of the phenomenon and the ability to reveal it. I really appreciate your suggestions but at the moment I can not deepen them. I am interested in the use of infrared to increase the performance of the LRL, to obtain discrimination and for the operation even with fresh buried gold.
Best Regards

[enjoykin4]

Thank you Signore Franco !!

Best regards ! :)
enjoykin4

[enjoykin4]

Hi enjoykin4,
Unfortunately I'm away from my laboratory, I have to watch my wife here and I have no electronic instrument, only a tester. I own a digital and an analog oscilloscope and many electronic components but unfortunately they are in Italy. I think that's always a good idea to share knowledge and experience, it's the only way to progress. I thought a lot before posting my LRL on the forum, but then I felt it was the best and I would have got benefits too. I wanted to confirm the proper functioning and maybe someone might improve it. I have helped many people privately with email and one confirmed to me a very good find, and this made me very happy. This was the only way to keep alive the forum. First it was a long series of disputes between believed in the phenomenon and others who ironically also denied the existence of the phenomenon. I now believe that there are no doubts about the existence of the phenomenon and the ability to reveal it. I really appreciate your suggestions but at the moment I can not deepen them. I am interested in the use of infrared to increase the performance of the LRL, to obtain discrimination and for the operation even with fresh buried gold.
Best Regards

CIAO SIGNORE FRANCO

How do you do - and our wife to ?

To obtain discrimination with our LRL's make experiments with variabile pulse trains. As you well know like 50 years experienced electronic constructor - simple single pulse have infinite series of sinus (or cosinus) frequencies - and theoreticaly has an infinite power.

Remember the Great Nikolai Tesla work. He has used very high amplitde more than 12 000 000 Volts and extremelly sharp nano (or pico) impulses to excite etherical froces in his Magnificient Collorado-Springs transmitter. And he got the results.

I think that golden signals are part of this etherical force which influent classical EM-field so the reulsts can be obtained with much lower amplitudes. Remember Mineoro golden-cells cavities - in fact cylindrical capacitors because Maxwell displacement currents in non-polarised capacitors are nothing less or more to tha longitudinal scalar waves which are not electromagnetic in nature. Capacitor is a kind of conversion tube between those two natural filelds.

If you are interested in modulation signal envelopes - feel free to contact me at email
enjokin4@yandex.ru

ps: I think it is no sense to public here many thinks i know because many people here has not pure and clean intention.

Best regards
enjokin4

[FrancoItaly]

Hi enjoykin4,
At the moment the conditions of my wife are stationary and require my continued presence so I can only dedicate myself to the theory of LRLs, but as I said I am very interested to infrared rays, by comparing the signal provided by my LRL and the one provided by a infrared system it could be possible a sort of discrimination. I am preparing a similar system to the pulse induction, where there is a pulse transmitted by an infrared LED and a receiving part, another infrared LED, a kind of infrared radars. Soon I'll post the schematic so someone can experience it. As for the impulse of which you speak I have some experience with the construction of electronic musical instruments, electronic organs in particular, according to the Fourier analysis the square wave contains only odd harmonics of decreasing amplitude and for obtaining a sawtooth wave is necessary to add to square wave his higher octaves with decreasing amplitude. Thus only with square waves (easily available with frequency dividers) was possible to have a sound with odd and even harmonics. As a boy I also repaired the radios and I used a square wave generator (about 1000Hz), a signal tracer useful to inject the signal even in the high frequency stages as the harmonics easily arrived in the Mhz range.

Best Regards

[enjoykin4]

Hi enjoykin4,
At the moment the conditions of my wife are stationary and require my continued presence so I can only dedicate myself to the theory of LRLs, but as I said I am very interested to infrared rays, by comparing the signal provided by my LRL and the one provided by a infrared system it could be possible a sort of discrimination. I am preparing a similar system to the pulse induction, where there is a pulse transmitted by an infrared LED and a receiving part, another infrared LED, a kind of infrared radars. Soon I'll post the schematic so someone can experience it. As for the impulse of which you speak I have some experience with the construction of electronic musical instruments, electronic organs in particular, according to the Fourier analysis the square wave contains only odd harmonics of decreasing amplitude and for obtaining a sawtooth wave is necessary to add to square wave his higher octaves with decreasing amplitude. Thus only with square waves (easily available with frequency dividers) was possible to have a sound with odd and even harmonics. As a boy I also repaired the radios and I used a square wave generator (about 1000Hz), a signal tracer useful to inject the signal even in the high frequency stages as the harmonics easily arrived in the Mhz range.

Best Regards

Dear Franco I have not experience in the construction of electronic musical instruments, electronic organs and other electoinic instruments but i have experience in physic's experiments.

If you make some experiments with nano-pulses in HV domain you will see that envelope of nano-pulses have almost perfect sawtooth wave shape - so it have infinite superpositions of both odd and even harmonics over wide frequenc range. If you succedd to make an Unipolar nano-impulse you will get pure potential impulse with zero current running. This kind of impulses are basic of scalar longitudinal waves. So am pretty sure that gold treasure radiate above described zero current - high potential impulses (remember burnt front-end LRL electronics of Alonso Geo and many others LRL hunters). And yes they (nano-impulse) influent E-field of your telescopic antenna and parallel tank-circuit changing amplitude and phase of your LRL. And they deca with 1/r law.

Best Regards from Russia
Enjokin4

[Qiaozhi]

This kind of impulses are basic of scalar longitudinal waves. So am pretty sure that gold treasure radiate above described zero current - high potential impulses (remember burnt front-end LRL electronics of Alonso Geo and many others LRL hunters).

There is a much higher probability that the LRL front-ends you refer to were damaged by ESD, and not some mysterious force emanating from buried treasure.

[enjoykin4]

There is a much higher probability that the LRL front-ends you refer to were damaged by ESD, and not some mysterious force emanating from buried treasure.

Ok folks.

Long time ago in 1903 year Schwarzschild introduced "Electrokinetic potential L" which is L= (φ-v·A), so folks it is over 100 years more since the scalar product v·A was recognized as a potential. It is a pure potential.

Electrokinetic potential (L) is really a potential difference which when multiplied by the charge density forms a relavistic invariant. The E-field seems to me is much more sensible to change of electrokinetic potential if the electrokinetic potential is capable of doing work in a fixed case where were the sum (φ+v·A), not the difference.

An charge q moving at velocity v through an A (vector potential) field can be considered to have a kinetic potential v·A, or a kinetically derived potential energy q(v·A).
Maximum energy is when v is parallel to A, when the charge travels along the A field, and has a value qAv . This is in exact agreement with the energy available from the motion derived E-field and with the energy extracted from the source of the A field.

ps: Some people here need much more experimenting and as much as possible empty talking and conclusions based on personal final phantasies !! :D

[WM6]

Schwarzschild only re-invented (in 1903) what was introduced by Clausius as electrodynamic potential in 1857.

And all was pure futile speculations that was never transformed in any sort of working device (on contrast with Maxwell mathematical "speculations").

This is proved also by "some people here" who desperately begging on the forum for any schematic and at the same time spread here kilometers barren and wild "phantasies" which have never been tested in practice experiments by themselves.

[enjoykin4]

Schwarzschild only re-invented (in 1903) what was introduced by Clausius as electrodynamic potential in 1857.

And all was pure futile speculations that was never transformed in any sort of working device (on contrast with Maxwell mathematical "speculations").

This is proved also by "some people here" who desperately begging on the forum for any schematic and at the same time spread here kilometers barren and wild "phantasies" which have never been tested in practice experiments by themselves.

.................................................. .................................................. .......
Seems to me some Slovenian members here need comeback to primary school
.................................................. .................................................. .......

ps: Nobody @begging@ for nothing !! Presenting an working schematic with purpose of further design improvements acording to newest principles of scalar physics is the main goal here - not like in some Slovenian country where some people (like WMGURU6) have had sucked cosmic widsdom from little finger and sell own speculations for "SHNOBEL PRIZE". Typical Slovenian WMGURU6 did just in that way.

Folks tell me for only one Slovenian world class inventor or world class scientsist ??
THE FACT .... There is NO ONE - except mabe WMGURU6 with his CLONES of Tesla's antennas !! :lol: :lol:


ps: @never been tested in practice......@ :lol: :lol:

OPEN YOUR MIND IF YOU CAN WMGURU6 - THIS IS RUSSIAN SCALAR TECHNOLOGY I WAS TALKING ABOUT !!
I GUESS SLOVENIAN WMGURU6 NEVER HAS SEEN SOMETHING SIMILAR IN THE SLOVENIAN WILDERNESS ..... :lol: :lol:

https://pp.vk.me/c629421/u43140286/video/y_5d8cc163.jpg

ASTA LA VISTA WMGURU6.


to Signore Franco only:
Signore Franco if you want your wife live further - obtain device i have told you. It is not a fake like all Slovenian CLONE Devices.

Best regards you and your wife signore Franco !!
Enjoykin4

[enjoykin4]

http://www.blogcdn.com/www.joystiq.com/media/2008/05/tmpphpjb3pc2-rose-tinted-glasses.jpg
WATCHING YOU NEW SCHNOBEL->WMGURU6 !!


I guess Slovenian WM6GURU does not know what his favorite mountain "ТРИГЛАВ" menas.
Little help: СВАРОГ-ПЕРУН-ВЕЛЕС.... Мир ПРАВИ


Of course he doesnot know because it is a pure Russian terminology. Not so long Slovenia and whole Europe had been small part of GRANDE TARHTARIA ..... destroyed in Kosheys's nuke attacks before somthing more than 200 years.

******************** More anti-Jewish remarks removed *********************

Everthing can be found in Taniya, Torah, Cabbal..

The Darkness shell cover the earth and fog darkness the nations .....

But happily for us night of Svarog have been over 1996 after 1008 years of Koscheys experiments.....

Wanna know more or would put your heads in the sand ??

[WM6]

I GUESS SLOVENIAN WMGURU6 NEVER HAS SEEN SOMETHING SIMILAR IN THE SLOVENIAN WILDERNESS ..... :lol: :lol:

https://pp.vk.me/c629421/u43140286/video/y_5d8cc163.jpg



On contrary, all this is cheap trick for naive soul's only.

If you uncover winter greenhouse with strawberries and then let snow to fall to them, you get exactly the same fraudulent picture. Wake up.

The same fraud as all Russian commercial available LRL's, you promote here on forum.

But Tesla inventions are worth to further research, despite not with dismantling those crappy LRL's.


PS: This is real sparrow comment, not fake one like winter strawberries:

http://i65.tinypic.com/vnjfkn.jpg

Sorry Franco, to help signore enjoykin4 to pollute your extra tread - Strawberries are my weak point.

[FrancoItaly]

Hi Carl
Now You have a different opinion on Lrls? It is now 10 years that I participate in this forum and I was skeptical myself, but later I changed my mind, especially after building several all functioning. My conviction was strengthened by the fact that other forum members have achieved the same performance, particularly thank Geo which I really appreciate his expertise in this field. I appeal to all those who have failed to make working my LRL to insist, to many I have given help privately, but I wish that the requests for help were on the forum so as to be useful to all although I know that in some countries the use of metal detectors is prohibited and therefore a person he wants to remain anonymous. As last thing I want on the forum could speak only on lrls and that the criticism is constructive and not insults.
Best Regards

[WM6]

Dear Franco

It is very clear (from description how your LRL works, given by our experienced friend Geo, too), that your design is able to work as geomagnetic line sensor only. In other words: some sort of primitive magnetometer. Not first such design seen on this forum.

Such devices can detect known buried targets only. If such devices are able to detect somewhere something not known/buried by hunter before, then this is pure coincidence, cause useful targets are buried everywhere. Proven by metal detectors.

But retain your hope. Live with hopes is most important in our life.

Best wishes.

[enjoykin4]

Dear Franco

It is very clear (from description how your LRL works, given by our experienced friend Geo, too), that your design is able to work as geomagnetic line sensor only. In other words: some sort of primitive magnetometer. Not first such design seen on this forum.

Such devices can detect known buried targets only. If such devices are able to detect somewhere something not known/buried by hunter before, then this is pure coincidence, cause useful targets are buried everywhere. Proven by metal detectors.

But retain your hope. Live with hopes is most important in our life.

Best wishes.


American English
BS = BULL S♠♠♠...... magnetometer !! :angry: :angry:


PERFECT ABSURD OF COPLETE IGNORANT MAN FROM SLOVENIAN MOUNTAINS (wilderness)

[FrancoItaly]

Hi WM6,
you do not know what you're talking about, we are not talking of dowsing or other "psychic" devices but totally electronic devices and only an expert in telekinesis succeed to be able to make it sound remotely. "Live with hopes is most important in our life", you are right, but we also say there are none so deaf as those who do not want to hear. In this forum you spend the time to criticize something you do not know and in this you are a perfect scientist, what can not be explained by current laws of physics do not exist and anyone who says it is a dreamer.
Best Regards

[WM6]

PERFECT ABSURD OF COPLETE IGNORANT MAN FROM SLOVENIAN MOUNTAINS (wilderness)



You are right, cause our strawberries are not results of extraordinary Trofim Denisovich Lysenko genetic science like yours.

[enjoykin4]

Hi WM6,
you do not know what you're talking about, we are not talking of dowsing or other "psychic" devices but totally electronic devices and only an expert in telekinesis succeed to be able to make it sound remotely. "Live with hopes is most important in our life", you are right, but we also say there are none so deaf as those who do not want to hear. In this forum you spend the time to criticize something you do not know and in this you are a perfect scientist, what can not be explained by current laws of physics do not exist and anyone who says it is a dreamer.
Best Regards


PERFECT RIGHT SIGNORE FRANCO about Slovenian mountain-dreamer !! :)

Read my post for you:
http://www.longrangelocators.com/forums/showthread.php?p=152841#post152841

Best regards
Enjoykin4

[WM6]

Read my post for you:
http://www.longrangelocators.com/forums/showthread.php?p=152841#post152841



Eh, mio caro signore tavarisc Winter Strawberjich Lysenko, what would be your next great LRL invention?

[taxma1981]

This lrl work fine,
https://youtu.be/l3nH9CG0lI8

[WM6]

Evidently.
It can detect U-boot at 1 cm distance.

[taxma1981]

I have marks and outside in nature

[Geo]

This lrl work fine,
https://youtu.be/l3nH9CG0lI8

my VLF (made in china) also makes the same:lol:

[taxma1981]

This is the lrl franko with 4046 not mein

[Geo]

Hi Franco.
What is happening when your lrl catch the phenomenon (or locates the buried coins)?
1. At xtal version, at emmiter of tr5 and
2. At pll version , at pin2 of 4046
Voltage increase or decrease??

Regards

[FrancoItaly]

Hi Geo,
With xtal version voltage increases at emitter of Tr5 with the phenomenon, with pll version the voltage decreases at pin 2.

Best Regards

[Geo]

Hi Geo,
With xtal version voltage increases at emitter of Tr5 with the phenomenon, with pll version the voltage decreases at pin 2.

Best Regards

Thank you Franco:)

[RIMES]

thanks

[Bill512]

Hi Geo,
With xtal version voltage increases at emitter of Tr5 with the phenomenon, with pll version the voltage decreases at pin 2.

Best Regards

Franco, in my PLL the voltage increases.
More specifically, the voltage measurements at pin 2 was not reliable ,because the interference from the probes was enormous.
So instead of pin 2 , the voltage at the R4-C5 node and also at R5-C6 node was measured.
For example, from an initial voltage of 3V this voltage goes to 3.5 or even to 4.5V in case of strong "signals".
I don't consider this as a problem, is just info.

[FrancoItaly]

Hi Bill512
It's possible that the voltage increases, this depends on the phase of the amplified signal compared to that of the VCO 4046, the critical point is in the TR1 stage that's drived by a pulse signal. Probably C3, TR1 and P2 can be eliminated and you can connect directly C8 and pin 4.
Best Regards

[Geo]

I reinstated the audio at normal position (it was reverse) and fixed the case.
Now Franco's lrl is ready for T.H......:cool:

[WM6]

Nice! Look like indestructible design.

Geo you should put on it "Made in EU" "Manufactured in Greece".

[Geo]

No, i don't like "EU":angry:.
I am sure that you understand why????

:)

[WM6]

No, i don't like "EU":angry:.
I am sure that you understand why????

:)

So I provoke you.

What material you use for housing, FR4 (Cu plated vitroplast) or it is wood in whole?

[taxma1981]

Lrl franko
http://s28.postimg.org/vt27f96ex/20160225_163948.jpg (http://postimg.org/image/vt27f96ex/)

[Geo]

So I provoke you.

What material you use for housing, FR4 (Cu plated vitroplast) or it is wood in whole?

Wood with foil......:lol:

[pigeon]

Wood with foil......:lol:

hi all friends

anyone have o complet projet.

thank you

[WM6]

Dear friend

695 posts in this thread (including this one).

A couple of finished Franco's devices and you are still asking for "complet projet"?

Maybe you need to read this thread from start.

[Geo]

hi all friends

anyone have o complet projet.

thank you

The project is a little critical. I sujest you to read carefully all the posts so to understand it and to give carefull at some points. Best version (most easy) is the 8Mhz xtal
Good luck

[WM6]

Good work walkman. Congratulations.

[pigeon]

just like this : D
hi walkman

you have the pcb

thanks. you are a good man

[brs]

7805 ؟
or 7812

[FrancoItaly]

Hi walkman,
very good work, the IC is 7812 as all the lrl functions at 12V.
Regards

[WM6]

Hi walkman,
very good work, the IC is 7812 as all the lrl functions at 12V.
Regards

In this case power supply should not be 12V as marked on PCB, but something near to 15V.

[FrancoItaly]

the power supply is 18 V (2 X 9V battery) the IC is 7812 that, yes, requires more than 15V. Usually for low battery voltage I fixed 16V then an operating range from 18V (full charge) to 16V.

[abdou2014]

Nice Work Walkman :)

[Sneshko]

just like this : D

Very good walkman!
... or IC1 that will be 7812 and not 7805?
Regards! :)
Sneshko

[abdou2014]

THANK YOU MR WALKMAN :)

[pigeon]

Thanks very much friends. I updated pcb

:)thank my friend you are a good man

[FrancoItaly]

Hi Walkman,
Have you already tried the LRL in the field?

[Sneshko]

Thanks very much friends. I updated pcb

Bravo walkman!
Congratulations and thank you for PCB!
Now it's OK!
Write about your test results.
Thanks in advance!
Sneshko

[enjoykin4]

Ја имам Гео-Радар Zond 12e са три сонде. Види линкove:

http://accuratelocators.com/ground-penetrating-radar/zond-12e.html?p=2

http://accuratelocators.com/ground-penetrating-radar/zond-12e.html

https://www.youtube.com/watch?v=wbGYjAYlTkY

Цена би била 15.000 евра фиксно.


Dear sneshko

Stll selling GPR for 20,000 bucks ?? :oh: :oh:

http://accuratelocators.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/z/o/zond-300mhz-antenna.png

You must be one of the Reachest GOLD HUNTERS (lot of Golden coins) in Serbia if you have such kind od proffesional equipment in your prospecting menu!! :)

Would you like to share with us your personal experience in work with this very expensive professional equipment ?? I am interesting in real detection depth and precision of underground mapping software at real hard soil - hot rocks and highly mineralized ground !!


ps:
http://nigma.ru/?s=Sneshko+lrl&t=web&rg=t%3D%D0%9C%D0%BE%D1%81%D0%BA%D0%B2%D0%B0_c%3D%D 0%A0%D0%BE%D1%81%D1%81%D0%B8%D1%8F_&rg_view=%D0%9C%D0%BE%D1%81%D0%BA%D0%B2%D0%B5&yn=1&gl=1&rm=1&ms=1&yh=1&av=1&nm=1&lang=all&srt=0&sf=1


Best regards :)
Enjoykin4 !!

[enjoykin4]

Dear signore Franco !!

What do you think your LRL crystal version can work at 10GHZ - 12GHz ?? :)

https://upload.wikimedia.org/wikipedia/commons/thumb/3/33/LNB_dissassembled.JPG/220px-LNB_dissassembled.JPG

No it is not a joke Franco. :) I have plans to modify one old LNB (low noise block) from my old satellite antenna 1.8m dish - make simple feedhorn antenna at 10Ghz-12Ghz and use his very temperature stable and compensated VXO with integrated pin diodes amplitude detector at output. For signalization like you did - 10 highly bright led diodes in VU meter row.

Input oscilating circuit can be easy tunned at higher or lower freq. using integrated dielectric resonators for strip line waveguides matching. Also bandwidth can be adjusted at some range with tunnable short circuited stubs for both horizontal and vertical polarizations.

Maybe this .... 10GHZ-12GHZ version is secret to miles away long range distances ?? :oh:
Who knows ????


Ps: Also i wish to hear your professional oppinion and advice about Russian long range locator IGA-1. Would you like to analyse schematics and give your prfessional sugestions about this device ?? It is not so hurry to me - so when you find some time will be fine to hear from your about behaviour of two low drif PID regulator loops of IGA-1.

Correct name from Russian is Geophysics Anomaly Sensor !!
http://www.iga1.ru/pribor/iga1pol.jpg
http://superbiorezonans.9bb.ru/uploads/000c/67/df/942-1-f.jpg

Check this Jura's site
http://www.juras-projects.org/eng/index.php

Jura's LNB schematic of Lumax LX-LST40
http://www.juras-projects.org/files/lumax_lx-lst40.png

Best regards
Enjoykin4

[FrancoItaly]

Hi enjoykin4,
I do not know if such high frequencies can be operated, without a doubt in the sky there are many transmitters that can "excite" the phenomenon, but would not know how to adapt my LRL at these frequencies, perhaps it would be better to study a new circuit. As regards the long range locator IGA-1 at first glance it seems a selective amplifier that can work on different frequencies but I have problems with the Russian language, however it seems a passive receiver as the Zahori.

Best Regards

[brs]

hi franco
Are minerals buried a meter deep and a half Ahumicr logic far from the transmitter towers and communication do you need with a passive receiver transmitter stimulates buried metals and if it was necessary to send Is there a circle

[brs]

Do you sense to be a transmitter stimulates metals

[brs]

Use language translator weak

[FrancoItaly]

You mean a kind of radar? Transmit on one frequency and receive on another frequency?

[ouiarabe]

Thanks very much friends. I updated pcb


Hello
thank you very much for your help walkman but I think your PCB has some errors

[pigeon]

hi friend ouiarabe

is it possible to correct errors


thank you and best time

[WM6]

As regards the long range locator IGA-1 at first glance it seems a selective amplifier that can work on different frequencies ...

..... however it seems a passive receiver as the Zahori.



If even.
At least Zahory iz able to detect something (static charge), not so IGA-1 which is pure waste box.

[ouiarabe]

hi friend ouiarabe

is it possible to correct errors


thank you and best time

salut

1- - According to the scheme Franco Italy, the buzzer is connected to the pin OUT1 IC B are not to pin 2 to IC A

2--Look this photo there is a track to add

[pigeon]

salut

1- - According to the scheme Franco Italy, the buzzer is connected to the pin OUT1 IC B are not to pin 2 to IC A

2--Look this photo there is a track to add

thank you

yar7im waldik

[Nicolas]

http://www.imagesco.com/geiger/geiger-counter-tubes.html

http://www.imagesco.com/geiger/digital-geiger-counter.html

http://uzzors2k.4hv.org/index.php?page=rs232geiger_counter

http://www.imagesco.com/articles/geiger/build_your_own_geiger_counter_-_gm_tube.html

http://www.imagesco.com/geiger/geiger-graph.html

https://www.elektormagazine.com/magazine/elektor-201111/19753

[Sneshko]

Dear Nicolas!
Thank you for Radiation Meter!
Coming strange time ... who knows? Perhaps all of us this device will be necessary...
Can you put it on forums for a free download and Programmed controller ATmega88PA-PU?
Regards!
Sneshko

[Nicolas]

Dear Nicolas!
Thank you for Radiation Meter!
Coming strange time ... who knows? Perhaps all of us this device will be necessary...
Can you put it on forums for a free download and Programmed controller ATmega88PA-PU?
Regards!
Sneshko

Hello friend welcome.
Try to get it from the site i think is not free.
I not have built it and not have the firmware sorry. only i have put to give information for all here to try it.

[enjoykin4]

Hi enjoykin4,
I do not know if such high frequencies can be operated, without a doubt in the sky there are many transmitters that can "excite" the phenomenon, but would not know how to adapt my LRL at these frequencies, perhaps it would be better to study a new circuit. As regards the long range locator IGA-1 at first glance it seems a selective amplifier that can work on different frequencies but I have problems with the Russian language, however it seems a passive receiver as the Zahori.

Best Regards

Hello Franco !!

Signore read how this ********************************************** AGAINST HIGH-END RUSSIAN LRL DETECTOR IGA-1. {75meter detection distance for underground water veins is very nice result for LRL !!) :)

***** Personal attack deleted *****
Regards
Enjoykin4

[Nicolas]

[QUOTE=enjoykin4;153054]
Hi dear enjoykin4.

Please need respect for all other members see this the third insult and not respect. i not have what do here go elsewhere or stay and speak with much respect we are all here for knowledge please and not be racist stay tolerant.

Because i see this behavior for person ignorant lacking knowledge or awareness in general; uneducated or unsophisticated. :angry:

[enjoykin4]

Dear Nicolas!
Thank you for Radiation Meter!
Coming strange time ... who knows? Perhaps all of us this device will be necessary...
Can you put it on forums for a free download and Programmed controller ATmega88PA-PU?
Regards!
Sneshko


Hello dear Serbian Sneshko !!

Yes very strange times .... i like to say ..... ***** DELETED ABUSE *****
Downloading link
https://www.elektormagazine.com/files/magazine/2011/dolo/110538-11.zip



Дозиметр Сталкера for SERB SNESHKO !!http://www.longrangelocators.com/forums/showthread.php?p=153057#post153057

http://radiokot.ru/circuit/digital/measure/60/12.jpg


***** DELETED *****

Best regards
Enjoykin4

[Nicolas]

[QUOTE=enjoykin4;153056]
Thank you Ukrainian so much interesting this projects. But relax my friend friend ;)

[Geo]

Hi Franco.
Did you tried to give signal from generator to antenna (not directly but from some distance)?
I tried it yesterday, connected a wire 25cm to output of generator and put it at sweep operation from 65 to 165Mhz so to see where the coil of lrl is tuned. I put the antenna of lrl parallel with generaotr aerial and near to 30 cm. I did not found any frequency that lrl is tuned and the sensitivity was very low. At lrl i use a 3 turns coil with 22pf capacitor parallel with coil. Also i tried the same experiment with fm modulation but without good results (for me). Any experiment from you or any idea????

Regards

[brs]

hi Geo
Try it with bc238

[Geo]

My xtal lrl works ok.
I try to understand how exactly the phenomenon acts on it so to try make it more sensitive

[FrancoItaly]

Hi Geo,

I don't have a FM generator but I tried with an oscillator ( only 1 transistor) tuned in FM range and I had the same results, nothing, only a signal very close to antenna. The origin of the phenomenon remains for me always a mystery. However, the resonant circuit is important because if I change the values the LRL is not working. With 2 turns for L1 the lrl it's working also without 22pF as there is the parasitic capacitance of base-emitter junction.

Best Regards

[Geo]

I put the transistor on base so to make changes at mixer transistor and now lrl works better:lol:, maybe any bad soldering at pins of transistor. Now i have strong signal from 30cm distance. Lrl receives signals at 82...85Mhz and 87...88 Mhz. I"ll try to change teansistor with other types and to replace the 22pF with a variable capaqcitor (trimmer) so to change frequences. Do you think that is better to try at frequences highter than 108Mhz ????

Regards:)

[FrancoItaly]

Hi Geo,

If you have time you may try the range 60 - 200Mhz, the BC... series work also at 200Mhz and the trimmer it's a good idea. You can also test if there is some discrimination changing LC resonance.

Best Regards

[Geo]

Hi Franco.
I will inform if any change will give better results.
""Phainomenon"" is a very strange phainomenon....:lol:

[Qiaozhi]

enjoykin4 - Having just spent several minutes erasing your abusive posts, rants, and derogatory pictures, it appears that you may be incapable of reading the forum rules. In particular, please read this ->

***********************************************
LRL forums historically have a tendency to bring out the worst in some people. Personal attacks and taunts will not be tolerated. This includes verbal (you're an idiot) and pictorial (posting a derogatory picture). Violations will result in an infraction and possible suspension.
***********************************************

You have already had a number of warnings, and this is your very last chance.
One more abusive post and you're out!

[enjoykin4]

***********************************************
You have already had a number of warnings, and this is your very last chance.
One more abusive post and you're out!

.................................................. .............................



OK AMERICAN SMARTY !!

I AM GOING TO MUCH BETTER PLACE THAN YOUR FORUM IS !!

YOU HAVE MY FINAL PERMISSION TO DELETE ALL MY POSTS AND ACCOUNT AT THIS FORUM !!

ASTALAVISTA MUCHACHOS !!

Enjoykin4
Enjoykin4@YANDEX.RU
http://vk.com/images/gift/237/96.png

ps: Ну ладно. Даже если Вы увидите Знания у человека, который предлагает их использовать, Вы не сможете это сделать, ТАК КАК В Вашей ПРОГРАММЕ НЕТ ЭТОГО ЭЛЕМЕНТА. :D

http://rnto.club/img/up/images/new-knowlenge.jpg

[Geo]

Hi Franco.
I will inform if any change will give better results.
""Phainomenon"" is a very strange phainomenon....:lol:

I replaced the transistor of mixer with a BF240 and now the xtal version is more sensitive. Now it receives the signal from generatior more far than 3m with a good signal. I also connected a μammeter so to "see" if a change is negative.
Next days will go to field for test
Regards:)

[FrancoItaly]

Hi Geo,

Good idea, BF240 is a true RF transistor also, I think, with less beta gain, but if DC out is OK then the lrl should work equally.

Regards

[Geo]

Hi Geo,

Good idea, BF240 is a true RF transistor also, I think, with less beta gain, but if DC out is OK then the lrl should work equally.

Regards

Hi Franco.
First.. i tried it at Multisim and gives 2x more signal at output of mixer compared with BC183.
I did not measure the DC out but it seems to work perfect.

Regards

[brs]

hi franco
hi friends
lrl Must be Work near Radio stations
Stay away if Broken sense to be a transmitter
I want to transmitter pcb or Electronic circuit
and how much the transmitter frequency.To penetrate the ground ,mhz , khz or hz ??

[FrancoItaly]

This thread is not for this, physics of metal detectors is not the same of the lrls.

Regards

[fmnotes]

Hi Geo,

Good idea, BF240 is a true RF transistor also, I think, with less beta gain, but if DC out is OK then the lrl should work equally.

Regards

What exactly transistors can be replaced with BF240????
1 , 2 , 3 or 4 transistors.
You can be noted in the schematic???
thank's

[FrancoItaly]

TR1 with quartz version and TR2 with CD4046 version.

[Arionas]

TR1 with quartz version and TR2 with CD4046 version.



http://postimg.org/image/gjj2jx2zv/
http://postimg.org/image/v47ww6g99/

[FrancoItaly]

I post the two versions again.

[FrancoItaly]

Here the rest of the LRL, the power is supplied from two 9V batteries connected in series for a total of 18V. In the version with 3 LEDs it is not represented but the power supply stage is the same as the version with 1 LED.

[fmnotes]

Thank's Franco

[Mohlrl]

Hello Mr. Franco. Thank you for your efforts and providing device. I built 8mhz quartz version with bc237b transistor (I had access only to this transistor). The output voltage of device is 4.3 volts. When I'm close to the antenna my hand,one light led went off. But device don’t react to mobile. Device performance is good? Thanks for expressing your opinions. One movie is attached.
http://www.uploadmb.com/dw.php?id=1460808977

[FrancoItaly]

Hi Mohlrl,

the behavior is ok, you only need a test on the field with a long buried target.

regards

[Mohlrl]

Thanks very much for Help Mr Franco

[RIMES]

Hi Mr Franco;
Mr Franco thank you, I have made your device with 8 MHz, but the antenna I used the model shown in the picture attached (a single round of 8 centimeter diameter) and when I touch with my hand the LED lights, is it good?
http://www.longrangelocators.com/forums/showpost.php?p=139152&postcount=600