Gold Gun AL718

[ishtar hunter]

Hi to all
Does anyone have a schematic of the gold gun AL 718 transmitter? This receiver works well but i don't have the original transmitter and my transmitter does not match well with Receiver.
please help me.

[WM6]

Hi Ishtar, how do you expect that original transmitter will work better than yours?

If transmitter is tuned at the same frequency than receiver, then all is ok.

But probably you transmitter emit too much power, or you put it to close to receiver and so transmitter signal suppress all other useful signal. Al718 works on very long wave and need distance to proper wave polarization. You need very weak transmitter and antenna that can be oriented in all directions to get proper wave polarization. Even so transmitter should not be to close to receiver. Play with this, rather than asking for original transmitter which will not solve your problem.

[reza vir]

Hi to all
Does anyone have a schematic of the gold gun AL 718 transmitter? This receiver works well but i don't have the original transmitter and my transmitter does not match well with Receiver.
please help me.

see this circuit :)

[Geo]

This schematic is wrong....

[ishtar hunter]

Hi Ishtar, how do you expect that original transmitter will work better than yours?

If transmitter is tuned at the same frequency than receiver, then all is ok.

But probably you transmitter emit too much power, or you put it to close to receiver and so transmitter signal suppress all other useful signal. Al718 works on very long wave and need distance to proper wave polarization. You need very weak transmitter and antenna that can be oriented in all directions to get proper wave polarization. Even so transmitter should not be to close to receiver. Play with this, rather than asking for original transmitter which will not solve your problem.

Hi wm6 thank's so much .i attach my home made lrl picture and Operating frequency. this lrl work very good .i can find void and i dig so find void but in 5 khz for gold(I had adjust for Gold) in my Country(iran) this frequency detect iron . when i detect so dig i find iron so i change to 118 khz for gold and this problem was solved . voltage for gold is 6 volt on 118 khz -this detector can operate for gold 118 khz -silver 6khz-bronze 7 khz - void- diamond 90 khz. main voltage is 12 volt and all Output frequencies are stable and does not change during the search . I've used a bunch of aluminum with Bearings to connect antenna.(Sorry Tim Williams for the use of their logo).

[goldfinder]

In my chart of the elements where I derived the frequency the frequency of 5 khz for gold is very close to the frequency of one of the oxides of iron as both have close to the same atomic weight. Frequency is directly correlated with weight. The 118 khz is an upper harmonic if gold and far enough away from the upper harmonics of iron oxide that you can use it.
Goldfinder

[ishtar hunter]

In my chart of the elements where I derived the frequency the frequency of 5 khz for gold is very close to the frequency of one of the oxides of iron as both have close to the same atomic weight. Frequency is directly correlated with weight. The 118 khz is an upper harmonic if gold and far enough away from the upper harmonics of iron oxide that you can use it.
Goldfinder
Thank's my friend

[Tim Williams]

That's one fancy lrl. You know people well think I made that unit with my logo on it.

Tim

[reza vir]

In my chart of the elements where I derived the frequency the frequency of 5 khz for gold is very close to the frequency of one of the oxides of iron as both have close to the same atomic weight. Frequency is directly correlated with weight. The 118 khz is an upper harmonic if gold and far enough away from the upper harmonics of iron oxide that you can use it.
Goldfinder

very thanks my dear :)

[Geo]

Hi.
Does anyone has the schematic from the audio (amplifier lm386) of AL718 or Al707???


Regards

[reza vir]

Hi.
Does anyone has the schematic from the audio (amplifier lm386) of AL718 or Al707???


Regards

do you think this schematic ???

[reza vir]

LM386 datashet :)

[Geo]

LM386 datashet :)

Thanks but i need the exactly (original) schematic of the audio amplifier from GG.

[dojranski]

Geo This is the original scheme gold gan al 707 ..
if you can help
http://s14.postimg.org/lsuvmck00/sema_4.jpg
http://s16.postimg.org/m0ttd15vo/sema_4.jpg

[dojranski]

Geo This is the original scheme gold gan al 707 ..
if you can help
http://s14.postimg.org/lsuvmck00/sema_4.jpg
http://s16.postimg.org/m0ttd15vo/sema_4.jpg
http://s8.postimg.org/g5h5jtiic/IMG_0918.jpg

[Geo]

http://s8.postimg.org/g5h5jtiic/IMG_0918.jpg

Thank you!!!:)

[Geo]

Hi.
Does anyone has info about the portable transmitter and TX antenna for GoldGun???

Regards:)

[mustefa ubram]

Hi.
Does anyone has info about the portable transmitter and TX antenna for GoldGun???

Regards:)
hi geo
you can use the amplifire with mosfet output and coil antenna
G.L

[Geo]

Hi.
I am interesting for the original schematic or block diagram.
For example... a friend told me that the transmitter has at the out a transformer and the one end of transformer is going to the earth and the other is not connected
Is it true????

[Qiaozhi]

Hi.
I am interesting for the original schematic or block diagram.
For example... a friend told me that the transmitter has at the out a transformer and the one end of transformer is going to the earth and the other is not connected
Is it true????
Here's the schematic, if that helps.

[Geo]

Here's the schematic, if that helps.

Hi Qiaozhi.
This is the schematic of pistol, not from the external transmitter for areas where the signal is very low
:)

[apogonos]

Giorgos done only for large objects the GG

[Geo]

Giorgos done only for large objects the GG

Hello Taki, how are you????
Of course GG is for big treasures, but there are some tips!!!!!:cool:

Regards:)

[Qiaozhi]

Hi Qiaozhi.
This is the schematic of pistol, not from the external transmitter for areas where the signal is very low
:)
Don't think I've ever seen the schematic for the portable transmitter.

[Geo]

Me too.
Maybe Tim has it because i think that when he opened the AL718 he had also and the portable Tx.

[mustefa ubram]

Hi.
I am interesting for the original schematic or block diagram.
For example... a friend told me that the transmitter has at the out a transformer and the one end of transformer is going to the earth and the other is not connected
Is it true????
hi geo
yes .This method may be applicable.but The most convenient method is the use of electromagnetic waves.Reflected waves at the metal.You can get these waves with the receiver ferrite
G.L

[Geo]

hi geo
yes .This method may be applicable.but The most convenient method is the use of electromagnetic waves.Reflected waves at the metal.You can get these waves with the receiver ferrite
G.L

Hi.
I know the methods but i am looking for the method that used by accurate locators.

:)

[Barbarossa]

maby can use the am local radio fricouncies

[takhslambos]

is this gold gun test it ? is it working?

[takhslambos]

is someone own a gold gun al 707 or 718 to tell us t he resolts???

[Geo]

is someone own a gold gun al 707 or 718 to tell us t he resolts???

No good...

[takhslambos]

No news is a good news........is any member test the gold gun????

[Geo]

I wrote to you, No good results.
Before 2 weeks i had with me one AL707 original and one clone with some modifications. I found a object with my lrl, but nothing with two gold guns. But i will play a little with it yet.

[takhslambos]

The object that you found how big was? Like a coin???

[WM6]

The object that you found how big was? Like a coin???



Even smaller.

No problem to find such a small thing by LRL-ing, if you finally do "pinpoint" by metal detector.

But, wait, why would we even use the material creations as LRL's?

Why do we not detect treasure directly by our inner "soul powered LRL"?

Have you ever heard of out of body experience and out of body vision? Google a little for this term.

This way, you cannot to see treasure in soil only, but you can see back in time how this treasure was buried and by whom.

I expected mr. hung to be master of long range out of body vision, and not to bother with material mineoro and alike LRL crap.

http://link.springer.com/article/10.1007%2FBF01078246#page-1

[Geo]

The object that you found how big was? Like a coin???

Near to 5 Lt...

[AurumKid]

Geo This is the original scheme gold gan al 707 ..
if you can help
http://s14.postimg.org/lsuvmck00/sema_4.jpg
http://s16.postimg.org/m0ttd15vo/sema_4.jpg

http://s8.postimg.org/g5h5jtiic/IMG_0918.jpg

this links not working anymore.

Please Help!!! anyone can give me GG AL707 Schematic?

[taxma1981]

I have made the a718 and it works fine, I have made ​​changes to the coils, transistors, transmitters 3-4 mark I have daily, I've tuned to 19,58.evry day doing experiments on, other times I have good signal yet others not, can someone be seen in the hours SITE transmitter operation etc.

http://sidstation.loudet.org/data-en.xhtml


http://s16.postimg.org/6p6gn3mf5/Specgraphmmm.jpg (http://postimg.org/image/6p6gn3mf5/)
http://s18.postimg.org/uftpp4zet/IMG_20141022_211729.jpg (http://postimg.org/image/uftpp4zet/)

[AurumKid]

thanks mate.

how would you able to simulate it using android fone? can you link me how?

regards

[taxma1981]

will connect the output from the golden gun in the microphone of the mobile phone

[taxma1981]

the coils vice versa WRAPPED together by 922 rpm each and inductance with 59.6 mh, the distance between the 1-2 mm
http://s16.postimg.org/4nh3n402p/IMG_20141023_151602.jpg (http://postimg.org/image/4nh3n402p/)

One coil 922,together 1844, and 59.6 mh

[AurumKid]

Hi Taxma

Thanks for your input. I will try your modif of GG.

Best Regards

[taxma1981]

http://youtu.be/v9jDxCQZ6rM

[Sneshko]

Very good!
Bravo taxma1981!!!
Regrads!
Sneshko

[taxma1981]

the question is what caught;

[Nicolas]

http://youtu.be/v9jDxCQZ6rM

Good Friend

But what mean the counter please? How to find Gold with this Gold Gun please..How number off counter for Gold for silver and .....

Nicolas

[taxma1981]

at one point from three directions to do this thing, uploads
http://youtu.be/dYVMDeORWoE

[Nicolas]

at one point from three directions to do this thing, uploads
http://youtu.be/dYVMDeORWoE


Thanks to reply my friend but it's not clear to find the treasure...,,maybe can locate the direction but not the treasure it's so har to find it....

Good wishes and success

[taxma1981]

BURIED in gold what to do the voltmeter;

[taxma1981]

Good evening, I can fix it with ltc1968:)


http://www.bdtic.com/Linear/LTC1968.html




Another simple solution but is not quite right with the use of four diodes (bridge) The voltmeter will work again but will not count 100%

[taxma1981]

http://youtu.be/GVpsx0o-6Ic

[Nicolas]

http://youtu.be/GVpsx0o-6Ic

Good evening, I can fix it with ltc1968:)


http://www.bdtic.com/Linear/LTC1968.html





BURIED in gold what to do the voltmeter;

Where here show us please that... and please look your private I have send you message about RMS Panel

[taxma1981]

Nicοlas I can not send you a message, writes that we can not accept messages

[Nicolas]

Nicοlas I can not send you a message, writes that we can not accept messages


Now you can :):):) or look your email i have send you email.

Message I need help Sent Date Read Date
Sent to: taxma1981 (http://www.longrangelocators.com/forums/member.php?u=5569) 10-21-2014 04:30 PM 10-22-2014 08:41 PM
This is my Email ridha.nick@gmail.com
my question is where I can buy the RMS panel

give me link or other Idea and thanks

[taxma1981]

check your email nicolas

[taxma1981]

http://youtu.be/m-qhcnNRKLc

[taxma1981]

https://www.youtube.com/watch?v=60UnshoMByA



:lol:

[Nicolas]

https://www.youtube.com/watch?v=60UnshoMByA



:lol:

Hi Taxma if you make a transmitter is so better to test your Gold Gun

this transmitter is between 0- 100kHz and you can go to 300 Khz it simple to build it

only need make good calcul for value of C and R

F= 1 [1.4xRxC ]

[taxma1981]

separately transmitter or on the Gold Gan;

[Nicolas]

separately transmitter or on the Gold Gan;

Certainly separately and make tracer by gold gun since fews meter ten or twenty to tune it

you can build with three capacitors 1nF for 100Khz other 10nf for 10khz other 100nF for 1 khz

like the fisher 82 khz and 8.2khz and 820 Hz

[taxma1981]

hear people say it does not work with its own transmitter, How about you; I HAVE COORDINATED 19.58 khz and has importance every day,,sorry for my English

[Nicolas]

hear people say it does not work with its own transmitter, How about you; I HAVE COORDINATED 19.58 khz and has importance every day,,sorry for my English

Yes ok I understand that but if not have transmitter in your region you can make that. but I speak about resonance to catch Gold or metal by this frequency
if your gold gun work with this frequency mean receive only the frequency send by transmitter not by metal and that is wrong dear and not find Gold we need the resonance not need frequency of transmitter. here is many VlF transmitter in world

https://www.youtube.com/watch?v=WnoI9c8eqi4&feature=youtu.be Part #1
(https://www.youtube.com/watch?v=WnoI9c8eqi4&feature=youtu.be)

[Nicolas]

https://www.youtube.com/watch?v=xkECD199ZkQ&feature=youtu.be part #2 (https://www.youtube.com/watch?v=xkECD199ZkQ&feature=youtu.be)

[taxma1981]

The point is that a 555 can not do something on his own, nice video NIKOLAS

[taxma1981]

https://www.youtube.com/watch?v=0dxXXGc3NyY&feature=youtu.be

[taxma1981]

new antenna 61 mh

http://postimg.org/image/aevocm4kj

[Long Ranger]

Hi to all
Does anyone have a schematic of the gold gun AL 718 transmitter? This receiver works well but i don't have the original transmitter and my transmitter does not match well with Receiver.
please help me.

I believe I may have gotten the Gold Gun al707 to work--but, I got too close to some power lines...now it has lost most of it's sensitivity. It now needs to be checked out by someone who can replace capacitors etc.

I need Carl to sell me his Gold Gun! :)

[Long Ranger]

I have reason to believe that the Gold Gun is an excellent--and, a workable Receiver, if one can simply get the proper transmitter interfaced with it. As a Stand-Alone, it is of little if any use at all. Before I burned something on the circuit board, I got a reading of 850 mVolts, at just under one mile distance (0.82). It's a known gold mine, owned by a friend, in NE Washington State. It's a complex ore type lode. I got another good reading with my now defunct Gold Gun Al 707--that I have yet to check out, with with my White's Sierra Madre--with 25' or 15' Karbowski coil. I really love that setup. Also have the White's Pulse Scan TDI, with 16' Nugget Finder coil.

While I've had great success with a swivel rod and my transmitters--I have not been content to leave "well enough alone". With my Architraun System, I have been able to get very consistent audible / metered signals, on targets the size of a jewelry box, at three hundred feet. It is all well in the realm of known and established physics. More than that, I do not care to say. If it were broadly known--it would totally revolutionize metal detection systems, forever! It's a cat that could never be put back into the proverbial bag.

I've also learned how to take frequency readings from Google Earth Images. I have named that the Eagletraun System. This too, has proven to be quit successful for me. I actually pinpointed six dore' bars, in Texas, while I was in Central Washington. And, there is much more to that story, that will have to be put on hold, until I can work out an agreement, with the land owner, with respect to the main deposit--which I also pinpointed, with the Eagletraun, from a distance of aprox 2k miles.

[Long Ranger]

Hi to all
Does anyone have a schematic of the gold gun AL 718 transmitter? This receiver works well but i don't have the original transmitter and my transmitter does not match well with Receiver.
please help me.

A friend gave me his al-707. Both ferrite rods were broken, as a result of careless handling. It is now pretty much junk. If I could find another one cheap, I would see what I could do with it.

[Mike(Mont)]

Seems easy enough to replace and rewind the ferrite rods. Pretty sure somewhere there is a schematic that shows what it needed. I haven't worked with one but I know the rods have a spacing between the ends and this might need to be tuned.

[taxma1981]

Does anyone know in the circuit of the gold gun what is this blue or red cable that starts from the input of the mpf102 and where does it go?


https://ibb.co/kgFyBLq

[Pahom]

Does anyone know in the circuit of the gold gun what is this blue or red cable that starts from the input of the mpf102 and where does it go?


https://ibb.co/kgFyBLq
There is a board on the first page, you will find the answer there.

[taxma1981]

ground the one input of the coil through a 1 nf capasitor in series;

[Pahom]

ground the one input of the coil through a 1 nf capasitor in series;

Right . Amazing installation. It?s probably more convenient for the manufacturer to do this.